Publicité
Les langues disponibles
Les langues disponibles
Leveling the Laser
As long as the laser is properly calibrated, the laser is self‑leveling.
Each laser is calibrated at the factory to find level as long as it
is positioned on a flat surface within average ± 4 ° of level. No
manual adjustments are required.
If the laser has been tilted so much that it cannot self‑level (> 4 °),
the laser beam will flash.
When the beams flash as noted above THE LASER IS NOT LEVEL
(OR PLUMB) AND SHOULD NOT BE USED FOR DETERMINING OR
MARKING LEVEL OR PLUMB. Try repositioning the laser on a more
level surface.
Using the Pivot Bracket (Fig. N–P)
The laser has a magnetic pivot bracket (Figure N,
attached to the unit.
WARNING: Position the laser and/or wall mount on
a stable surface. Serious personal injury or damage to the
laser may result if the laser falls.
•
The bracket has a keyhole slot (Figure O
hung from a nail or screw on any kind of surface.
•
The bracket has magnets (Figure P) which allow the unit to
be mounted to most upright surfaces made of steel or iron.
Common examples of suitable surfaces include steel framing
studs, steel door frames, and structural steel beams. Before
attaching the pivot bracket against a stud (Figure P
place the Metal Enhancement Plate (Figure P
opposite side of the stud.
Using the Drop Ceiling Bracket (Fig. Q–S)
The laser is packaged with a drop ceiling bracket
drop ceiling bracket contains a steel plate and attaches to the
9
magnetized pivot bracket
The drop ceiling bracket is equipped with both 1/4 ‑ 20 and 5/8 ‑
11 female threads on the bottom of the unit.
These threads are to accommodate current or future D
accessories. Refer to Figures R and S for examples of accessories
sold seperately.
Using the Target Card (Fig. T)
Some laser kits include a Laser Target Card (Figure T) to aid in
locating and marking the laser beam. The target card enhances
the visibility of the laser beam as the beam crosses over the card.
The card is marked with standard and metric scales. The laser
beam passes through the semi‑transparent plastic and reflects
off of the reflective tape on the reverse side. The magnet at the
top of the card is designed to hold the target card to ceiling
track or steel studs to determine plumb and level positions. For
best performance when using the Target Card, the D
should be facing you.
MAINTENANCE
Your power tool has been designed to operate over a long period
of time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
9
) permanently
10
) so it can be
11
12
) on the
13
. The
(Figure Q).
WALT
e
WALT logo
e
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
The charger and battery pack are not serviceable.
D
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals for
cleaning the non‑metallic parts of the tool. These chemicals
may weaken the materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any
liquid get inside the tool; never immerse any part of the tool
into a liquid.
Optional Accessories
WARNING: Since accessories, other than those offered by
D
WALT, have not been tested with this product, use of such
e
accessories with this tool could be hazardous. To reduce
the risk of injury, only D
should be used with this product.
),
Consult your dealer for further information on the
appropriate accessories.
Service and Repairs
nOTE: Disassembling the laser level(s) will void all warranties on
the product.
To assure product SAFETY and RELIABILITY, repairs, maintenance
and adjustment should be performed by authorised service centres.
Service or maintenance performed by unqualified personnel may
result in a risk of injury. To locate your nearest D
go to www.2helpU.com.
Storing Your Laser
Do not store your laser in the kit box if the laser is wet. The laser
should be dried first with a soft dry cloth prior to storage.
Warranty
Go to www.2helpU.com for the latest warranty information.
TROUBLESHOOTING
The Laser Does Not Turn On
•
Fully‑charge the battery pack and then reinstall it in the
laser unit.
•
If the laser unit is exposed to extremely hot temperatures, the
unit will not turn on. If the laser has been stored in extremely
hot temperatures, allow it to cool. The laser level will not be
damaged by pressing the on/off button before cooling to its
proper operating temperature.
EngLIsH
WALT recommended accessories
e
WALT service centre
e
33
Publicité
