Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
5.4 - Use of the movable table (Optional)
The machines in this series can be equipped, under request, with a movable table (fig.10a, page 3) that allows to split shorter logs.
The movable table must be positioned on the work surface and locked with the security pin (A in fig.10b) paying attention to insert it completely and
fixing it with the 'R' shaped security pin (B in fig.10b)
IIf the movable table is to be used, the stroke of the wedge must be adjusted to prevent this hitting the table itself and damaging it.
On the right side of the machine, inside the beam, there is the automatic return rod.
Approximately in the middle of the rod there are two holes in which the split pin in equipment must be inserted (fig.11, page 4 - upper hole=for
VSD12 / lower hole=for VSD17). This will ensure that the wedge will perform the correct run so that it does not touch the table.
WARNING
Never operate the machine if the dowel is not fully inserted or if it is not locked with the 'R' shaped security pin.
Never operate the machine with the movable table if the adjustment described above has not been carried out as it may be
seriously damaged and the operator could be injured.
5.5 - Assembly and use of the 4-way wedge (Optional)
The log splitter can be equipped, even under request, with an optional 4-way wedge to split logs into four pieces with a single stroke.
The 4-way wedge (1 in fig.9, page 3) must be assembled directly on the standard 2-way wedge (2 in fig.9).
When the wedge is in position, insert the dowel (3 in fig.9) into the corresponding hole and into the hole (4 in fig.9) on the 2-way wedge in order to
secure it.
This 4-way wedge is used in the same way as the 2-way wedge taking care, however, not to split very hard wood or wood with a large number of
knots as the use of 2 wedges instead of 1 causes greater stress on the wedge.
WARNING
Never use the 4-way wedge if it has not been secured into position with the dowel supplied, as this could prove very dangerous
for both the operator and the machine.
5.6 - Closing the cylinder for transport
Before lifting and moving the log splitter, the cylinder must be lowered as follows:
•
Position a piece of wood under the wedge, on the work surface (fig.6, page 3)
•
Activate both the control levers (2 in fig.1, page 2) in order to lower the wedge completely (fig.6)
•
Release the right lever (2 in fig.12, page 4) in order to hold the wedge in the reached position.
•
Remove the cylinder check pins (fig.8a and 8b, page 3) and put them in the appropriate places on the two sides of the cylinder (fig.7, page 3).
•
Release also the left lever, therefore activate the right lever upwards until it clamps, in order to close the cylinder
•
When the cylinder is completely closed and the wedge raised from the piece of wood, bring the right lever (2 in fig.12) back to the neutral position
Now the log splitter can be lifted, moved and transported
WARNING
NEVER MOVE THE LOG SPLITTER WHEN THE CYLINDER IS LIFTED. THE MANUFACTURER IS NOT LIABLE FOR INJURY TO PERSONS,
ANIMALS OR OTHER THINGS CAUSED BY TRANSPORTING THE LOG SPLITTER WITH THE CYLINDER LIFTED.
5.7 - How to transport the log splitter
Before moving the log splitter, it is necessary to lower the cylinder (1 in fig.1, page 2), to close the side arms (3 in fig.1) and to raise the foot (B in fig.4,
page 2).
Attach the machine to the 3-points of the tractor and lift it for the transport.
5.8 - Manual handling of the log splitter (only with AXLE+WHEELS+HANDLING LEVER OPTION)
The log splitter can be equipped, under request, with wheels for minor movements and the relative handling lever for safe, trouble-free transport of
the log splitter.
Insert the axle (A in fig.16, page 5) in the appropriate hole in the oil tank, insert the wheels (B in fig.16) on the axle and fix them with the locking pin (C
in fig.16)
Fix the handling lever (D in fig.16) to the upper position of the 3-points attachment for the tractor (E in fig.16).
Now the manual handling of the log splitter is possible by using the lever.
28
ENGLISH
D22002000 - ver.2 - UPD 291209
Publicité
Table des Matières
