Refrigerator Compartment - V-ZUG Ideal 60i Mode D'emploi

Réfrigerateur et congelateur
Masquer les pouces Voir aussi pour Ideal 60i:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

5.1.1 Setting the child lock
To activate the setting mode:
u Press the Quick Cool button
w The Menu symbol is shown on the display,
flashes on the display.
w
c
To switch on the function:
u Confirm by briefly pressing the Quick Cool button
Fig. 2 (2) .
appears on the display.
w
c1
u Confirm by briefly pressing the Quick Cool button
Fig. 2 (2) .
Fig. 2 (7) , lights up on the
w The child lock symbol,
display.
flashes on the display.
w
c
w The child lock function is switched on.
If the function is to be switched off:
u Confirm by briefly pressing the Quick Cool button
Fig. 2 (2) .
appears on the display.
w
c0
u Confirm by briefly pressing the Quick Cool button
Fig. 2 (2) .
flashes in the display.
w
c
w The child lock function is switched off.
To end the setting mode:
u Briefly press the On/Off button
w The temperature display shows the temperature again.

5.2 Refrigerator compartment

5.2.1 Refrigerating food
u Store perishable foods such as ready-to-eat meals, meat
and sausages in the coldest area. Place butter and
preserves in the top area and in the door. (see 1 Appliance
at a glance)
u Use reuseable plastic, metal, aluminium, glass containers
and foil wrap to store food.
u Always store raw meat and fish in clean, sealed containers
on the bottom shelf of the refrigerator, to prevent them
coming into contact with or dripping onto other foods.
u Foods that easily absorb or give off smell or taste, as well as
liquids, should be stored in sealed containers or covered.
u Use the front area of the base shelf only to temporarily set
down refrigerated foods, for example while rearranging or
sorting the contents. Remember not to leave refrigerated
foods here as they could shift to the back or tip over when
you close the door.
u Do not pack foods too closely together, as the air needs to
circulate.
5.2.2 Setting the temperature
The temperature depends on the following factors:
-
the frequency of opening the door
-
how long the door is open for
the room temperature of the installation location
-
-
the type, temperature and quantity of the food
Recommended temperature setting: 5 °C
An average temperature of approx. -18 °C is then established
in the freezer compartment.*
The temperature can be adjusted continually. Once the 1 °C
setting is reached, the sequence starts again at 9 °C .
w The new setting is adopted approx. 5 seconds after the
last time the button was pressed and the set temperature
displayed again. The temperature in the interior gradually
adjusts to the new value.
* Depending on model and options
Fig. 2 (2) for around 5 seconds.
Fig. 2 (5) .
Fig. 2 (1) .
5.2.3 QuickCool
QuickCool selects the lowest cooling temperature. This option
is for very low temperatures:
-
In the fridge compartment
-
If the appliance is taller than 177 cm:*
-
In the freezer compartment
Use QuickCool to quickly cool large quantities of food.
If the appliance is taller than 177 cm:*
To freeze food, activate QuickCool when you place the goods
in the appliance.
Quick Cool uses slightly more energy.
Activating QuickCool
u Briefly press the Quick Cool button
Fig. 2 (6) symbol lights up on the display.
w The QuickCool
w The cooling temperature drops to the lowest setting.
w If the appliance is taller than 177 cm:*
w The freezing temperature drops to the lowest setting.
w QuickCool is on.
w QuickCool turns off automatically. The appliance continues
in energy-saving Normal mode.
SwitchingQuick Cool off ahead of schedule
u Briefly press the Quick Cool button
Fig. 2 (6) symbol dims on the display.
w The Quick Cool
w Quick Cool is off.
5.2.4 Tray
Shifting or removing the trays
The trays are prevented from being pulled out accidentally by
pull out stops.
Fig. 3
u Adjust the height of the tray: To do this move the slots along
the supports.
u Lift the tray and pull it out towards you.
u To remove the tray completely, set it at an angle and pull it
out towards you.
u Push the tray back in at the desired height. The removal
stops must point downwards and be positioned behind the
front contact surface.
Disassemble the tray
u The trays can be dismantled
for cleaning.
5.2.5 Using the split tray
u Push the split tray under-
neath as in the illustration
Control
Fig. 2 (2) .
Fig. 2 (2) .
33

Publicité

Table des Matières
loading

Table des Matières