Eaton Crouse-Hinds Série Mode D'emploi page 10

fig 6: remove slip-on filter
fig. 7: insert filter
top
fig. 8: lamp is flashing
top
cover
screw
fig. 9: mounting the belt hook
B
B
10
Explosion protected portable searchlight
SEB 8, SEB 8 L, SEB 8 ADR, SEB 8 DIN, SEB 8 L DIN
On the bezel ring there are located spring-load-
ed cams (fig. 1, item 7) into which one slip-on
filter can be inserted (Mind: Insert from one
side only).
By turning the bezel ring (apx. 2 turns), the light
beam can be adjusted from short to long range
(fig. 1, item 6).
The swivel ling lamphead can be adjusted
through apx. 100° (page 2, fig. 1).
In order to increase the stability of the portable
searchlight, a slide provided on the bottom of
the battery container can be backwards pulled
out (page 2, fig. 2, item 1).
Safety functions of the portable searchlight:
The series SEB 8 portable searchlights feature
some functions that make their use simple and
safe.
Check in case of a broken filament – main lamp:
Should the main lamp fail during operation or
when being switched on, there will be an
automatic changeover to the pilot lamp. The
selected function of the switch position (steady
light or flashing light) and the diode display are
maintained.
Check of the pilot lamp:
While switching on the main beam lamp, the
searchlight checks the pilot lamp's state.
Should the latter be defective, the red LED will
pulse for some seconds (apx. 4 to 5 times).
Then the normal charge indication will appear.
If the pilot lamp is defective and the switch is in
"pilot light" position, the main beam lamp will
be operated with a lower current so as to obtain
the luminous intensity of the pilot lamp.
Deep discharge protection:
When the battery is nearly exhausted, there is
an automatic changeover to pilot light.
Should the battery's discharge be continued,
also the pilot lamp will be switched off.
Thus the battery's deep discharge will be
prevented and the battery be protected.
Mind! This mode will be a enabled in switch
positions "main beam" and "flashing main
beam". In position "pilot lamp" the deep
discharge protection will be disabled by the
A
bypass mode. (see bybass)
Bypass:
With the switch in "pilot light position, the
electronics will be bridged.This switch position
is marked with a yellow icon.
Due to this safety measure, the pilot lamp's
operation will be ensured even in the event of a
failure.
Attention!
In this mode of operation the lamp should
not be switched on unattended, since the
deep discharge protection in the interest of
personal protection "will not operate" .
Should go off due to low battery power, turn
the rotary switch to position "0" (OFF)
switch is in this position, the side lamp.
Remove the handheld spotlight immediately
from the hazardous area and as Abs.6:
Maintenance / Repair described, load switch
in "Service".
Reset:
Should the electronics be affected by external
influences (e. g. extremely strong electro-
magnetic radiation lying above the permissible
EMC level), the processor will automatically
effect a reset.
The display of the battery's charging state
(LED's) can extinguish.
The desired function of the searchlight is
reestablished by turning the switch to 0 "Off"
and then back to the desired function.
Now the light emitting diodes again indicate
the current charging state.
Note: By means of the bypass function, a
long-time failure can be bridged.
Check of the charging state (service):
Check of the charging function means that the
battery is charged/discharged and charged.
Thereat the electronics will establish the actual
battery's state affected by ageing.
This function ensures an optimum charge of the
battery, while the indication of the charging
state is calibrated (see safety function "Service"
in para. 6, Maintenance/Servicing).
Special Features of the SEB 8 ADR:
EC Type Approval pursuant to Directive 94/55/
EC (Directive on the approximation of the laws
of the Member States with regard to the
transport of dangerous goods by road)
This lamp version with the warning lamp
according to the Road Traffic Licensing
Regulations is supplied with a special orange
slip-on filters on the rear mount.
Removing the orange slip-on filter from the
mount.
To do this, swivel the supporting foot of the
slip-on filter towards the handle and then pull it
out and up. (Fig. 6).
Use as warning lamp with flashing function.
GB