Publicité
Les langues disponibles
Les langues disponibles
Anleitung_NSMS_4300_ZZ_SPK7:Anleitung KGSZ 3050 SPK1
GB
Achtung
Laserstrahlung
Nicht in den Strahl blicken!
Laserspezifikation nach
EN 60825-1+A1+A2
Laser Klasse 2
1894S-8x11
P: ≤ 1 mW
Ï: 650 nm
Protect yourself and your environment from
accidents by taking the appropriate precautionary
measures.
Do not look directly into the laser beam with the
naked eye.
Never look directly into the laser path.
Never direct the laser beam at reflecting
surfaces, persons or animals. Even a low output
laser beam can inflict injury on the eye.
Caution: It is vital to follow the work procedures
described in these instructions. Using the tool in
any other way may result in hazardous exposure
to laser radiation.
Never open laser module.
When the tool is not going to be used for an
extended period of time, the batteries should be
removed.
Noise emission values
The sawʼs noise is measured in accordance with
DIN EN ISO 3744; 11/95, E Din EN 31201; 6/93,
ISO 7960 Annex A; 2/95. The machine may
exceed 85 dB(A) at the workplace. In this case,
noise protection measures need to be introduced
for the user (ear-muffs).
Idle speed
Sound pressure level LPA
86 dB(A)
Sound power level LWA
99 dB(A)
„The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors
with a potential influence on the actual immision level
at the workplace include the duration of impact, the
type of room, and other sources of noise etc., e.g.
the number of machines and other neighbouring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved."
12
24.11.2008
5. Technical data
Asynchronous motor
230 V~ 50 Hz
Output
1800 W
Operating mode
Idle speed n
4800 min
0
Carbide-tipped saw blade
ø 210 x ø 30 x 2,8 mm
Number of teeth
Tilting range
-45° / 0°/ +60°
Mitre cuts
0° to 45° to the left
Sawing width at 90°
430 x 65 mm
Sawing width at 45°
300 x 65 mm
Sawing width at 2 x 45°
(double mitre cuts)
300 x 35 mm
Weight
Laser class
Laser wave length
Laser output
Laser module power supply
2 x 1.5 V Micro (AAA)
6. Before putting the machine into
operation
The machine must be firmly mounted in working
position, e.g. on a workbench, the base frame
supplied with the machine, or similar.
All the covers and safety devices have to be
properly fitted before the machine is switched on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machineʼs moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
7. Assembly
7.1 Setting up the saw unit (Fig. 1/2)
To adjust the turntable (8), loosen the locking
handle (10) by approx. 2 turns, which frees the
turntable (8).
Turn the turntable (8) and scale pointer (11) to
the desired angular setting on the dial (12) and
lock into place with the locking handle (10).
Lightly press the machine head (4) down while at
10:22 Uhr
Seite 12
S1
-1
24
20 kg
2
650 nm
≤ 1 mW
Publicité
