Charge Process, Charge Output 2 - ROBBE POWER PEAK Infinity 3 Notice D'utilisation

[ [ O O U U T T 2 2 S S E E T T U U P P
: :
T T I I M M E E 0 0 : : 0 0 0 0 : : 0 0 0 0
C C A A P P A A C C I I T T Y Y : :
: :
V V O O L L T T A A G G E E 1 1 2 2 . . 8 8 0 0 2 2 V V
C C U U R R R R E E N N T T : :
P P E E A A K K . . V V O O L L T T : :
[ [ O O U U T T 2 2 S S E E T T U U P P
: :
T T I I M M E E 0 0 : : 0 0 0 0 : : 0 0 0 0
C C A A P P A A C C I I T T Y Y : :
: :
V V O O L L T T A A G G E E
C C U U R R R R E E N N T T : :
P P E E A A K K . . V V O O L L T T : :
[ [ O O U U T T 2 2 S S E E T T U U P P
: :
T T I I M M E E 0 0 : : 0 0 0 0 : : 0 0 0 0
C C A A P P A A C C I I T T Y Y : :
: :
V V O O L L T T A A G G E E
C C U U R R R R E E N N T T : :
P P E E A A K K . . V V O O L L T T : :
Data, functions of Output 2
Parameter
Cell count / Battery voltage
Capacity
Charge current
Peak sensitivity
Pre-peak suppression
11.2 CHARGE PROCESS, OUTPUT 2
[ [ O O U U T T 2 2 C C H H A A R R G G E E
: :
T T I I M M E E 0 0 : : 0 0 6 6 : : 4 4 9 9
C C A A P P A A C C I I T T Y Y : :
: :
V V O O L L T T A A G G E E 6 6 . . 1 1 6 6 2 2 V V
C C U U R R R R E E N N T T : :
P P E E A A K K . . V V O O L L T T : : 6 6 . . 0 0 4 4 1 1 V V
[ [ O O U U T T 2 2 L L A A D D E E N N
E E N N D D : : D D E E L L T T A A P P E E A A K K
: :
T T I I M M E E 0 0 : : 1 1 6 6 : : 4 4 9 9
C C A A P P A A C C I I T T Y Y : : 4 4 8 8 6 6 m m A A h h
: :
V V O O L L T T A A G G E E 5 5 . . 7 7 2 2 6 6 V V
C C U U R R R R E E N N T T : :
P P E E A A K K . . V V O O L L T T : : 6 6 . . 1 1 9 9 6 6 V V
Operating Instructions
POWER PEAK Infinity 3
You can switch between the two charge outputs using
] ]
the 'OUT1/2' button. When you press the button, the dis-
play changes and looks as shown in the screen shot prin-
0 0 m m A A h h
ted here. If no battery is connected, the voltage displayed
at Output 2 is slightly below the input voltage.
A A U U T T O O
0 0 . . 0 0 0 0 0 0 V V
This value is displayed in the appropriate line. As soon as
] ]
a battery is connected, this line of the screen displays the
actual battery voltage (see screen shot).
0 0 m m A A h h
5 5 . . 3 3 1 1 2 2 V V
A A U U T T O O
0 0 . . 0 0 0 0 0 0 V V
To program the charge current you wish to use, you must
] ]
first rotate the '3-D hotkey' to mark the appropriate line,
then activate it. The numeric value is now shown in inver-
0 0 m m A A h h se video (dark background), and you can vary it within the
5 5 . . 3 3 1 1 2 2 V V
limits of 0.1 A to 2 A in increments of 0.1 A. If you select
0 0 . . 8 8 0 0 A A
the 'AUTO' setting, the charger automatically calculates
0 0 . . 0 0 0 0 0 0 V V
the optimum charge current.
NiCd and NiMH batteries
1 - 8 cells, automatic detection
100 to 9900 mAh
Auto or manual: 0.1 A to 2.0 A
8 mV / cell, fixed
3 minutes, fixed
] ]
Once you have set the data correctly, and the 'OUT 2
Setup' display is still on the screen, hold the '3-D hotkey'
pressed in for two seconds. You will hear an audible sig-
8 8 6 6 m m A A h h
nal to indicate that the charge process has started, and
0 0 . . 8 8 1 1 A A
the green LED lights up. The illustration printed here
shows such a charge process: it has been in progress for
6 minutes and 49 seconds at a current of 0.81 A.
The charge is terminated using the Delta-Peak process,
] ]
which operates with a fixed sensitivity of 8 mV / cell. The
second line of the screen shows the reason for the termi-
nation in flashing script. The end of the charge process is
confirmed by the charger playing the programmed melo-
0 0 . . 0 0 0 0 A A
dy, and at the same time the green LED flashes. The scre-
en now typically looks like the illustration printed here.
25
No.
8429