CASTLE Serenity Manuel De L'utilisateur page 5

CAUTION
ALL APPLICABLE BUILDING CODES FOR YOUR
LOCATION MUST BE FOLLOWED. IN AREAS WHERE
BUILDING CODES REQUIRE ADDITIONAL STEPS
TO THE INSTALLATION OF THIS PRODUCT NOT
INCLUDED IN THIS MANUAL, THE BUILDING CODES
WILL TAKE PRECEDENT AND MUST BE FOLLOWED.
CONTACT YOUR LOCAL BUILDING INSPECTOR TO
OBTAIN ANY NECESSARY PERMITS OR INSPECTION
GUIDELINES BEFORE INSTALLING THE PRODUCT.
• Contact local building or fire officials about
restrictions and installation inspection requirements
in your area.
• Contact your local authority (such as municipal
building department, fire department, fire
prevention bureau, etc.) to determine the need for a
permit.
• The Castle Pellet Stoves pellet stove is designed to
burn pellet fuel only.
• A working smoke detector is required and must be
installed in the same room as the stove.
• This stove is not intended for use in commercial
applications.
• Door and ash pan must be closed and latched during
operation.
• Notify your insurance company of pellet stove
installation.
• This installation must conform with local codes. In
the absence of local codes you must comply with
ASTM E1509, (UM) 84-hud, ulc/ordC-1482, and UCL
S627-2000.
• The structural integrity of the manufactured home
floor, wall, and ceiling/roof must be maintained.
• Keep combustible materials (such as grass, leaves,
etc.) at least three feet away from the flue outlet on
the outside of the building.
• This stove should not be used as the only source
of heat in the house. Power outages and periodic
maintenance will result in a total loss of heat.
• Do not leave hopper door open while unattended.
Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5 CST
All manuals and user guides at all-guides.com
CAUTION
INSTALLATION AND REPAIR OF THIS PELLET STOVE
SHOULD BE DONE BY A QUALIFIED SERVICE PERSON.
THE APPLIANCE SHOULD BE INSPECTED BEFORE USE
AND AT LEAST ONCE A YEAR BY A QUALIFIED SERVICE
PERSON. IT IS IMPERATIVE THAT THE CONTROL
COMPARTMENTS, FIRE BOX, AND THE CIRCULATING
AIR PASSAGEWAYS OF THE STOVE BE KEPT CLEAN.
THE OPERATION OF EXHAUST FANS SUCH AS
BATHROOM FANS, ATTIC
STARVE THE PELLET STOVE OF COMBUSTIBLE AIR
CREATING A NEGATIVE PRESSURE IN THE ROOM.
PROVIDE ADEQUATE VENTILATION OF THE ROOM
ACCOMPANYING THE PELLET STOVE. IF NOT, THE
PRESSURE SWITCH MAY SHUT OFF OPERATION OF THE
PELLET STOVE.
THE MOVING PARTS OF THIS STOVE ARE PROPELLED
BY HIGH TORQUE ELECTRIC MOTORS. THESE PARTS
CAN CAUSE SEVERE DAMAGE TO BODY PARTS THAT
GET NEAR THEM. KEEP ALL BODY PARTS AWAY FROM
AUGER AND FANS WHILE THE STOVE IS PLUGGED INTO
AN ELECTRICAL OUTLET. THESE MOVING PARTS MAY
BEGIN TO MOVE AT ANY TIME THE STOVE IS PLUGGED
IN.
THE VENT SURFACES CAN GET HOT ENOUGH TO CAUSE
BURNS IF TOUCHED. NONCOMBUSTIBLE SHIELDING OR
GUARDS MAY BE REQUIRED.
INSTALL VENT AT CLEARANCES SPECIFIED BY THE
VENT MANUFACTURER.
ALL VENTING JOINTS, WHETHER VERTICAL OR
HORIZONTAL, SHOULD BE MADE GAS-TIGHT WITH
RECOMMENDED SEALANTS SPECIFIED BY VENT
MANUFACTURER.
ACCORDING TO HUD
DEVELOPMENT) REQUIREMENTS, WHEN INSTALLED
IN A MOBILE HOME, THIS STOVE MUST BE GROUNDED
DIRECTLY TO THE STEEL CHASSIS OF THE MOBILE
HOME AND BOLTED TO THE FLOOR. DIRECT AIR
ACCESS MUST BE PROVIDED, USE A FRESH AIR KIT.
FOR USE IN THE UNITED STATES AND CANADA.
APPROVED FOR INSTALLATION IN MOBILE HOMES.
CASTLE PELLET STOVES, PRODUCER OF THIS
APPLIANCE, RESERVES THE RIGHT TO ALTER ITS
PRODUCTS, SPECIFICATIONS
WITHOUT NOTICE.
Operator's Manual
Serenity Pellet Stove
FANS, ETC. MIGHT
(HOUSING & URBAN
AND/OR PRICE
5