Nice MhouseKit SL1W Instructions Et Avertissements Pour L'installation Et L'utilisation page 33

TECHNICAL SPECIFICATIONS OF PRODUCT COMPONENTS
SL1W-SL10W is manufactured by Nice S.p.a. (prov. of Treviso – Italy). Nice S.p.a., in order to improve its products, reserves the right to modify their
technical characteristics at any time without prior notice. In any case, the manufacturer guarantees their functionality and fitness for the intended
purposes. Note: all the technical characteristics refer to a temperature of 20°C.
Model type
Type
Technology adopted
Peak thrust
Nominal torque
Speed (no load)
Nominal torque speed
Maximum cycles frequency
Maximum continuous cycle time
Application limits
Mains power SL1WC-SL10CW
Mains power SL1WC-SL10CW/V1
Max. absorbed power
Emergency power supply
"OPEN" input
"STOP" input
Radio Antenna input
Maximum cable length
Ambient operating temperature
Use in acid, saline or potentially
explosive atmospheres
Mounting
Protection rating
Dimensions / weight
Remote control compatibility
Memorisable GTX4 transmitters
Range of the GTX4 transmitters
Programmable functions
Self-programming functions
Radio protocol
Radio communication
Installable wireless accessories
Installable PH100W photocells
SL1WC
Electromechanical gearmotor for automation of automatic gates and doors with incorporated command
control unit, complete with radio receiver for "GTX4" transmitters.
24Vdc motor, reducer with helical gears; mechanical release. A transformer inside the motor, but
separate from the control unit, reduces the mains voltage to the nominal 24 V voltage used throughout
the automation system.
10 Nm
3.5 Nm
0.25 m/s
0.20 m/s
14 cycles/hour at 25°C
10 minutes
Its structural characteristics suit it to gates weighing
up to 400 kg and 5 m long.
230 V (+10% -15%) 50/60Hz
120 V (+10% -15%) 50/60Hz
370 W
Provision for "PR1" buffer battery connection
For normally open contacts (the closing of the contact causes the "OPEN" command)
For normally closed or normally open contacts and/or for constant resistance of 8.2 KΩ, or normally
closed contacts with self-recognition of the "normal" state (any variation from the memorised status
causes the "STOP" command)
52Ω for RG58 or similar type of cable
Mains power supply: 30 m; inputs/outputs: 20 m with antenna cable preferably shorter than 5m (observe
the warnings regarding minimum gauge and type of cables)
-20 ÷ 50°C
NO
On a horizontal plane using the appropriate mounting plate
IP44
300 x 163 h 295 mm / 7.5 kg
Using GTX4 transmitters, the control unit is able to receive one or more of the following commands:
"OPEN", "Partial Open", "Open Only" and "Close Only"
Up to 256 if memorised in mode 1
From 50m to 100m. This range can vary if there are obstacles or electromagnetic disturbances, and is
affected by the position of the receiving aerial incorporated in the flasher.
"Cycle" or "Complete cycle" (automatic closure) functionality
"Slow" or "fast" motor speeds
Pause time during "complete cycle", selectable from 10, 20, 40, 80 seconds
Partial opening type selectable in 4 modes
Obstacle detection system sensitivity, 4 selectable levels
"OPEN" command functionality selectable in 4 modes
Self-recognition of "STOP" device (NO, NC contact or 8.2 KΩ resistance) Self-recognition of gate length
and calculation of ramp down point
High security; compatible with the Power&Free System radio technology from Mhouse
Bidirectional, on 7 channels in band 868 MHz.
Maximum 20 units
Maximum 7 pairs
SL10WC
15 Nm
5.2 Nm
0.18 m/s
0.15 m/s
12 cycles/hour at 25°C
7 minutes
Its structural characteristics suit it to gates
weighing up to 550 kg and 7 m long.
420 W
300 x 163 h 295 mm / 8.5 kg
English – 31