Nice MhouseKit SL1W Instructions Et Avertissements Pour L'installation Et L'utilisation page 29

10.6.2 - Flashing indicator
The flashing indicators include LEDs that allow you to check their opera-
tional state at any time. For led "A" (fig. 45) see Table 15. For led "B" (fig.
45) see Table 16.
LED "A"
Off
1 fast red flash each second
2 fast red flashes + pause for
1 second
2 fast green flashes + pause
for 1 second
1 fast green flash followed by
1 fast red flash + 1 second
pause
1 flash per second, green on
the transmitter
(*) Note - If the indicator colour is red, one of the following problems may be identified: 1) The maximum number of daily manoeuvres has been
exceeded for a long period. - 2) The battery is old and should be replaced. - 3) The solar cell used as a solar charger is damaged. - 4) The device
does not receive sunlight and consequently cannot charge the battery.
If the battery is fully charged the led colour is green; otherwise it is red.
Led "B"
led LED B1 off
led LED B2 off
led LED B3 off
led LED B1 on
led LED B2 off
led LED B3 off
led LED B1 on
led LED B2 on
led LED B3 off
led LED B1 on
led LED B2 on
led LED B3 on
led LED B1 off
led LED B2 flashing briefly
once every 2 seconds (*)
led LED B3 on
(*) N.B.: This indications are only seen during the wireless device test (see paragraph 8.2 – Wireless device test)
B1 = MINIMUM signal level - B2 = MEDIUM signal level - B3 = MAXIMUM signal level
TABLE 15 (FL100W)
Status
Indication with batteries inserted: the device is
not powered or is faulty
Indication resulting from insertion of the battery
or pressing the key; the device is not paired
with any system (factory condition)
Indication resulting from the insertion of the
battery or the pressure of the key; the device
is not part of a network, and the procedure for
its installation has been activated and device
is waiting to be recognised by a control unit;
this procedure is activated when you insert
the battery in the device or by pressing the
keypad; it has a duration of 10 seconds from
battery insertion or from the last press of the
button, after which it deactivates automatically
if no control unit has recognised it
Indication following battery insertion when the
automation is stopped; the device is paired
with a system and is communicating correctly
with the control unit
Indication following battery insertion when the
automation is stopped; the device is paired
with a system but the control unit does not
communicate (could be switched off)
The automation is moving or in test
TABLE 16 (PH100W)
Status
The automation is in test phase or in stand
by; bad quality of radio signal received from
wireless device
The automation is in test phase; poor quality of
radio signal received from wireless device
The automation is in test phase; good quality
of radio signal received from wireless device
The automation is in test phase; optimum
quality of radio signal received from wireless
device
Automation in movement and solar panel
charging device batteries
During the manoeuvre the flashing indicator flashes once every second.
When something is wrong the flashes are more frequent (every half sec-
ond); the light flashes twice with a second's pause between flashes, see
Table 17.
Action
Check that the battery is inserted with the correct polarity; if it is
correct check the battery charge; if the battery voltage measure
is less than 1V the battery is empty; if the battery is charged it is
likely that the photocell is broken.
Normal operation; the photocell is ready to be learned by the
CL1W.
Normal operation; if you want the device in question to be
added to the system, activate the device recognition procedure
on the CL1W control unit.
Normal operation
Check that the automation is actually stopped, that there is no
testing procedure in progress, and that it is powered and not in
stand-by; if the previous tests are positive check the quality of
the radio signal received from the device
Normal operation; if the indicator colour is red, see the note (*)
Action
Insufficient radio communication; search for a better position
for the device
Limited radio communication; if possible, search for a better
position for the device
Normal operation
Normal operation
Normal operation
English – 27