Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Tab. 2 --- Sound pressure levels
Sound pressure levels, for measurement carried out with standard fan speed regulator (Variex).
Model
Model
50Hz
50Hz
SE 04
SE 05
SE 06
Indoor, free field at 2 m in front of
Indoor, free field at 2 m in front of
SE 08
the unit
SE 10
SE 13
SE 14
SC 04
SC 05
SC 06
Outdoor, free field at 2 m in front
Outdoor, free field at 2 m in front
SC 08
of the unit
of the unit
SC 10
SC 13
SC 14
Note:
Values are referred to an ambient temperature of 35_ C.
Sound pressure levels, for measurement carried out with standard fan speed regulator (Variex).
Model
Model
60Hz
60Hz
SE 04
SE 05
SE 06
Indoor, free field at 2 m in front of
Indoor, free field at 2 m in front of
SE 08
the unit
SE 10
SE 14
SC 04
SC 05
SC 06
Outdoor, free field at 2 m in front
Outdoor, free field at 2 m in front
of the unit
of the unit
of the unit
SC 08
SC 10
SC 14
2 --- Installation
CAUTION: the ambient unit must never be installed
outdoors.
2.1 --- Overall dimensions
See Fig. 1 and Fig. 2 for the overall dimensions of the
evaporating unit (SE) and of the external motor con-
densing unit (SC).
Fig. A --- Evaporating unit SE
English
Octave band frequency (Hz)
63
125
250
500
52
56
50
48
55
61
58
56
56
61
58
57
45
49
49
45
45
49
49
45
46
50
50
46
49
54
54
50
51
56
56
52
53
57
58
54
54
58
59
57
Octave band frequency (Hz)
63
125
250
500
53
57.5
57
53.5
60
61
56
54.5
63
60.5
57.5
59
43.5
47
51.5
46.5
47.5
51
55
50
49.5
53
57
52
57.5
62.5
57.5
54.5
53.5
58
61
57
54.5
59
64
61.5
2.2 --- Positioning the indoor unit
S Unpack the units as close to the place where it has
to be installed as possible. Once unpacked, avoid
stress any impact to its internal components.
S The air conditioner (indoor unit) can be installed
in any indoor location provided it is not exposed to
an aggressive ambient.
S Position the indoor unit next to the main heat
source.
S Fix the unit to the
ceiling or to the
wall by inserting 6
(SE 04--- 05--- 06)
or
8
08--- 10--- 13--- 14)
expansion
thorough clamps
(in this case en-
sure the clamp is
sealed) in the f8--- mm holes on the two side brack-
ets.
S Make sure the airflow circulate freely.
S To allow the servicing of the unit, the Service Area
showed in Fig. 5, has to be left unobstructed (in
Fig. 5c the 200--- mm minimum clearance from the
back of the evaporating unit is approximate. It has
to be left to ensure that the refrigerating lines can
be connected to the valves on the back panel).
2
Sound pressure level
Sound pressure level
1000
2000
4000
51
49
46
54
52
51
55
52
51
41
38
36
41
38
36
42
39
37
46
43
40
48
45
43
51
47
43
53
49
45
Sound pressure level
Sound pressure level
1000
2000
4000
49.5
47
44.5
56
54.5
52
60
59
56
43
39.5
36
47.5
44
40
49.5
46
42
50
49
44
52
50.5
46
57.5
53
48.5
(SE
or
Fig. B --- Detail of the clamp
[dB(A)]
[dB(A)]
55
60
62
47
47
48
52
54
56
58
[dB(A)]
[dB(A)]
56
61
65
49
53
55
57
59
63
Publicité
Chapitres
Table des Matières
