Kostal PIKO 36 EPC Guide D'installation Rapide page 12

Short manual
IMPORTANT INFORMATION
The inverter may only be installed, maintained and repaired by a trained and qualified
electrician. The electrician is responsible for ensuring that the applicable standards and
regulations are observed and implemented. Work that could affect the electrical power
system of the relevant energy supply company at the site of the solar power feed-in may
only be carried out by qualified electricians expressly authorised (licensed) by the energy
supply company. This includes changes to the factory pre-set parameters, e.g. using the
PARAKO parameterisation software.
It must be ensured that the L1-L3 phases on the inverter's AC terminal and the phases in the
grid are assigned uniformly.
This product may generate a direct current in the outer protective earthing conductor. If
protective residual current devices (RCD) or residual current monitoring devices (RCM) are
used, only type B RCDs or RCMs are permitted on the AC side.
The solar modules connected to the inverter must comply with Class A of the IEC 61730
standard.
This device is classified as equipment class A. It may therefore cause radio interference in
a domestic environment. If this occurs, the operator may be required to take appropriate
measures.
For initial commissioning, at least the "min. input voltage (U DCmin )" must be present and
there must be an output greater than the self-consumption of the inverter.
POSSIBLE DAMAGE
Risk of damage when the inverter is placed on its underside. Always place the inverter on its
rear side (cooling elements) after unpacking.
If the PV generators are incorrectly connected, the inverter may be damaged. Check the
connections before commissioning.
Installation
Perform inverter assembly, installation and commissioning based on the information provided in the
Installation chapter on page 60 onwards
.
Complete operating manual and warranty conditions
An in-depth operating manual and more information about the PIKO inverter and approved
countries in which the inverter can be used is available online at
www.kostal-solar-electric.com/Download/PIKO-Projektwechselrichter.
Information about the service and warranty conditions is provided in a separate document
available at
www.kostal-solar-electric.com/Download/Service.
22 © 2018 KOSTAL Solar Electric GmbH
Short manual
EU declarations of conformity
KOSTAL Solar Electric GmbH hereby declares that the inverter described in this document complies
with the basic requirements and other relevant conditions of the directives listed below.
Directive 2014/30/EU (on the approximation of the laws of the Member States relating to
n
electromagnetic compatibility (EMC))
Directive 2014/35/EU (on the harmonisation of the laws of the Member States relating to the
n
making available on the market of electrical equipment designed for use within certain voltage
limits – in short: Low Voltage Directive)
Directive 2011/65/EU (RoHS) to limit the use of certain hazardous substances in electrical and
n
electronic equipment
You will find a detailed EU Declaration of Conformity online at
www.kostal-solar-electric.com/Download/Zertifikate.
Contact details and service
If you have any technical questions, please contact our service hotline.
Country Phone
Germany +49 (0)761 477 44 - 222
Switzerland +41 32 5800 225
France +33 16138 4117
Greece +30 2310 477 555
Italy +39 011 97 82 420
Spain +34 961 824 927
Turkey +90 212 803 06 26
China +86 21 5957 0077-7999
© 2018 KOSTAL Solar Electric GmbH
DE
DA
EE
EL
EN
ES
FR
IT
E-mail
service-solar@kostal.com
service-solar@kostal.com
service-solar-fr@kostal.com
NL
service-solar-el@kostal.com
service-solar-it@kostal.com
service-solar-es@kostal.com
PL
service-solar-tr@kostal.com
service-solar-cn@kostal.com
PT
SE
TR
ZH
23