Assembly / Before Commissioning - Scheppach OSM600 Instructions D'origine

m ATTENTION!
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!

8. Assembly / Before commissioning

m WARNING!
Always pull the power plug before making adjust-
ments to the equipment.
• All covers and safety devices have to be properly
fitted before the equipment is switched on.
• It must be possible for the grinding/sanding belt
and disk to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws, etc.
• Before you actuate the On/Off switch, make sure
that the abrasive paper is correctly fitted and that
the equipment's moving parts run smoothly.
Connection to vacuum suction.
The use of an extraction system is recommended.
8.1. Tool changes (Fig. 3 - 8)
m ATTENTION! Turn off the machine and discon-
nect the main plug.
When changing tools make sure to have all parts
cleaned.
Prepare the appropriate tool and mount it as follows:
1. Insert cover (6) in table (2)
2. Insert stage plate (8) into the cover (6) (Fig. 4)
3. Attach the lower spindle disc (7) to the spindle (1)
(Fig.5).
4. Slide the abrasive sleeve (9) onto the rubber
sleeve (7) (Fig. 5).
5. Apply the disc (D) (use the correct measurements)
(Fig. 7).
6. Put on the hex-nut and tighten it with the hook
wrench (F). (Fig. 8)
Be sure always to mount the correct parts when
changing the abrasive sleeves. The table inlays have
to be bigger than the abrasive sleeves.
Note! The 13 mm abrasive sleeve is put directly onto
the spindle (1).
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Table:
Abrasive sleeve Table inlay
inside Ø inside Ø
13 mm 13 mm
19 mm 19 mm
26 mm 26 mm
38 mm 38 mm
51 mm 51 mm
8.2. Installing the abrasive belt (Fig. 9, 10)
m ATTENTION! Switch off the machine and pull
out the mains plug.
• Remove the abrasive sleeve (9), rubber sleeve (7),
stage plate (8) and cover (6) if already mounted.
• Guide the grinding belt attachment (10) over the
spindle (1) and the stud (G) into the groove provided
for this purpose.
• Also make sure that the recesses (H) on the attach-
ment are inserted into the notches. If the recesses
do not engage immediately, turn the abrasive belt
by hand until they engage.
• Screw washer (B) and locking screw (A) onto the
spindle (1).
8.3. Changing the grinding/sanding belt (11)
(Fig. 11)
• Pull out the power plug.
• Turn the grinding/sanding tensioner (13) to the right
in order to reduce the tension on the grinding/sand-
ing belt (11).
• Remove the grinding/sanding belt (10).
• Mount and the new grinding/sanding belt in reverse
order. Important. Note the running direction: On the
housing and on the inside of the grinding/ sanding
belt!
8.4. Adjusting the grinding/sanding belt (11)
• Pull out the power plug
• Push the grinding/sanding belt (11) by hand slowly
in the running direction.
• The grinding/sanding belt (11) must run centrally on
the grinding/sanding surface. If not, you can use
the knurled screw (14) to make adjustments.
8.5. Fasten stop (12) (Fig. 12)
• Insert the workpiece stop (12) with the recess in
the groove on the table and fasten with the fixing
screw (C).
Spindle disc
size
small 16 mm
medium 22 mm
medium 22 mm
large 44 mm
large 44 mm
GB | 25