Cleaning, Maintenance And Ordering Spare Parts - EINHELL TE-CI 18 Li BL Traduction Du Mode D'emploi D'origine

6.4 Battery capacity indicator (Fig. 3 / item 2)
Press the battery capacity indicator switch (3).
The battery capacity indicator (2) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED fl ashing:
The battery is empty, recharge the battery.
All LEDs fl ashing:
The battery pack has been deep-discharged and
is defective. Do not re-use or charge a defective
battery pack.
6.5 LED light (Fig. 4 / item 6)
The LED light (6) can be used in poor lighting
conditions to illuminate the area where you
want to screw. The LED light (6) comes on
automatically as soon as you press the On/Off
switch (5).
6.6 Changing the bit (Fig. 5)
Caution! Set the changeover switch (4) to its
center position whenever you carry out any
work on the cordless screwdriver (for example
changing the tool, maintenance work etc.).
Inserting the bit:
•
Insert the bit into the bit mount (1) as far as
the stop while simultaneously pulling the slee-
ve on the bit mount (1) toward the bit.
•
Release the sleeve again.
•
Then check that the bit is securely seated.
Removing the bit:
•
Pull the sleeve on the bit mount (1) toward the
bit, hold it tight and remove the bit.
6.7 Screws
It is advisable to use self-centering screws (e.g.
Torx, cross recessed head) as these will enable
you to work safely and reliably. Always make sure
that the bit used is of the same size and shape as
the screw.
Anl_TE_CI_18_Li_BL_SPK7_USA.indb 13 Anl_TE_CI_18_Li_BL_SPK7_USA.indb 13
EN
6.8 Removable holding clip (Fig. 1 / item 8)
When the holding clip (8) is fi tted, the equipment
can be hung e.g. on a belt. The removable holding
clip can be screw-fi tted to either the left or right-
hand side of the equipment. Fitting is possible but
not necessary.
7. Cleaning, maintenance and
ordering spare parts
HAZARD!
Always take the battery out of the equipment
before starting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
We recommend cleaning the equipment
immediately each time after use.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may
be aggressive to the plastic parts in the
equipment. Ensure that no water can get into
the interior of the equipment. The ingress of
water into an electric power tool increases the
risk of an electric shock.
7.2 Maintenance
There are no other parts inside the equipment
which require maintenance.
7.3 Ordering replacement parts:
Service
1. If your power tool requires service, con-
tact an authorized Einhell USA dealer or
call the Einhell USA customer service
center at 1-866-EINHELL
(1-866-346-4355). Only identical replace-
ment parts should be utilized for repairs. This
will ensure that the safety of the power tool is
maintained.
2. If the battery charger cable is damaged, it
must be immediately replaced to avoid a
hazard. Contact the Einhell USA
service center at 1-866-EINHELL
(1-866-346-4355) for assistance.
- 13 -
customer
®
12.11.2019 07:44:49 12.11.2019 07:44:49