Error Messages - Worx LANDROID Mode D'emploi

12. Error Messages

Symptom
Red light on
Red light flashing
Blue light on
18
Blue light flashing
NOTES
• Before turning power on, always check LANDROID
This message is displayed also when LANDROID
• If for any reason—i.e. a party, children playing...—you want to park your Landroid
®
. Landroid
mowing session. If you want to re-start it, press STOP Button (9), then press
• If an error repeatedly occurs in the same area of your lawn, you might have a problem with the boundary wire so
please refer to the previous installation instructions and check your set up with its help.
• If your lawn is divided in two separated areas, connected by a corridor less than 1m, one of which is not provided with
the Charging Base: when Landroid
the Main switch (8) to "I"(on), press
®
• If Landroid runs abnormally once in a while, please try to restart it. If the problem cannot be solved, please contact
WORX Service Agent for help.
• Do not wash the machine with a high pressure washer. This could cause damage to the battery or the machine.
Lawn Mowing Robot
Cause
®
Landroid is trapped.
®
Landroid is outside
working area.
Wheel motor blocked
Blade disc blocked
®
Landroid is lifted up.
®
Landroid is upside
down.
will go to its charging base and stay there. Please note Landroid
®
runs out of charge, take it manually to the Charging Base, turn power on by turning
and
1. Turn power off by turning the Main switch (8) to "O"(off);
®
2. Take Landroid to a lawn area free from obstacles;
3. Turn power on by turning the Main switch (8) to "I"(on).
4. If the error message is still displayed; turn power off; turn Landroid
upside-down. Check if there's any debris causing a blockage in the top cover
or check if there is anything preventing the wheels from rotating.
5. Remove any possible obstruction, turn the Landroid
®
1. If Landroid is actually outside its territory: turn power off by turning the
Main switch (8) to "O"(off), take Landroid
by turning the Main switch (8) to "I"(on).
®
2. If the Landroid is inside its territory, check the LED on the Charging
Base is green. If not, check the Charging Base is connected properly to the
charger and the charger is connected to a suitable power supply. If so, it
means that the boundary wire ends are clamped incorrectly, and you need
to reverse them.
3. If the LED light flashes green, check the boundary wire is well connected
to the clamps to the Charging Base. If the problem persists, check that the
boundary wire hasn't been cut.
1. Turn power off by turning the Main switch (8) to "O"(off); take Landroid
an area free from obstacles;
2. Turn power on by turning the Main switch (8) to "I"(on).
3. If the error message is still displayed; turn power off; turn Landroid
upside-down and check if there's anything preventing the wheels from
rotating.
4. Remove any possible obstruction, turn Landroid
1. Turn power off by turning the Main switch (8) to "O"(off);
®
2. Turn Landroid upside down and check if there's anything preventing the
blade disc to rotate.
3. Remove any possible obstruction.
®
4. Turn Landroid upright and take it to an area with short grass or adjust the
cutting height;
5. Turn power on by turning the Main switch (8) to "I"(on).
1. Turn power off by turning the Main switch (8) to "O"(off).
®
2. Take Landroid to a lawn area clear of obstacles, turn power on by turning
the Main switch (8) to "I"(on).
3. If the error message is still displayed: turn power off, turn Landroid
upside-down and check there's nothing lifted up.
4.Remove any possible object, turn Landroid
®
Turn Landroid upright.
®
is inside its territory. If not, the error indication light will flash red.
®
is sitting over the boundary wire when turned on.
, the charge process will start.
Action
®
upright, turn power on.
®
inside its territory. Turn power on
®
upright, turn power on.
®
upright, turn power on.
®
in the Charging Base: press
®
will now wait until the next scheduled
and to start mowing.
®
®
in
®
®
and
EN