Setting The Alarm - SOUNDMASTER DAB600 Manuel D'instructions

This unit has a dual alarm function.

SETTING THE ALARM

Press the "ALARM / SNOOZE" (13) button to enter the alarm menu, press the button ONCE to display 'Alarm
1.
1 set up' and press the button TWICE to display 'Alarm 2 set up'. Press the "SELECT" (7) button to accept
alarm of choice.
After selecting the alarm of choice, the hour digits will flash in the display. Use the "TUNING" ◄ or ► (5 or 6)
2.
buttons to select the correct alarm wake up hour and press the SELECT button to confirm. The minute digits
will start to flash.
Use the "TUNING" ◄ or ► (5 or 6) buttons to select the correct alarm minute and press the "SELECT" (7)
3.
button to confirm. The alarm duration will be displayed.
Use the "TUNING" ◄ or ► (5 or 6) buttons to select the duration (90, 60, 45, 30, 15 minutes) of choice and
4.
press the "SELECT" (7) button to confirm. The alarm source will be displayed.
Use the "TUNING" ◄ or ► (5 or 6) buttons to select the alarm source (Buzzer, DAB or FM) of choice and
5.
press the "SELECT" (7) button to confirm. If a radio source is displayed the radio source will now be displayed.
Use the "TUNING" ◄ or ► (5 or 6) buttons to select the wake up station (last station listened to or DAB
6.
preset) of choice and press the "SELECT" (7) button to confirm. The alarm frequency will now be displayed.
Use the "TUNING" ◄ or ► (5 or 6) buttons to select the alarm frequency ("Daily"=daily, "Once"=once,
7.
"Weekend"=weekend, "Weekdays"=weekdays) and press the "SELECT" (7) button to confirm. If 'once' is
selected then use the "TUNING" ◄ or ► (5 or 6) buttons to set the date that the alarm is to activate. Please
the select button to move to the next field in each case. When the date is set, the alarm volume will now be
displayed.
Use the TUNING (◄) or (►) buttons to select the desired wake up volume and press the SELECT button to
8.
confirm. The alarm status will now be displayed.
Use the "TUNING" ◄ or ► (5 or 6) buttons to select the status of choice (Off or On) and press the "SELECT"
9.
(7) button to confirm. This completes the set up procedure for the wake up mode.
Note

To set the wake up options for the second alarm, follow the above procedure using 'Alarm 2' from the alarm
menu.
ACTIVATING AND USING THE ALARM
1. Switch the radio into standby mode.
2. Press the ALARM / SNOOZE (13) button to display the current status of the alarms (e.g. Alarm 1: on and
Alarm 2:off).
Press the button again to change the status to the next one in the sequence below until the status of choice is
3.
displayed. Press the "SELECT" (7) button to accept. An active alarm is indicated by a corresponding alarm
icon (bell) in the display.
4. Once the alarm has been set and activated, when the time on the clock is the same as the alarm time that has
been set, the alarm will sound and the volume will gradually increase in volume to the one that has been set.
5. The alarm will continue to sound and stop automatically after the time interval that has been set. To silence
the alarm, press the "STANDBY " (3) button. If a repeat alarm has been set, the alarm indicator will remain
illuminated and the alarm will sound again at the next programmed day unless the alarm has been turn off.
To activate the snooze function, press the "ALARM / SNOOZE" (13) button when the alarm sounds. The alarm
6.
will silence, the display will display the clock and the snooze interval remaining and the (Zz) indicator. The
alarm will sound again after approximately five minutes.
To extend the snooze interval from the default 5 minutes, press the "Snooze" (13) button repeatedly after the
7.
alarm has been activated to scroll through the options available (5, 10, 15 and 30 minutes). When the snooze
interval of choice is displayed stop pressing the button and this interval will now be used as the default. The
"ALARM / SNOOZE" (13) button may be used repeatedly within the alarm activation time. To cancel the
snooze function; press the "STANDBY
To turn off the alarm permanently, follow step 3 until 'Alarm 1 off' is displayed. Press on the "SELECT" (7)
8.
button to select. The alarm is now off and the alarm symbol extinguishes.
Note

If both alarms have been activated, priority will be given to the alarm that has the earliest activation time. If
the snooze function is used for the first alarm and the activation time of the second alarm is within this
period, the second alarm will not activate. If setting two alarms with activation times within one hour of the
other one, always ensure that the alarm is silenced using the STANDBY
SETTING AND USING THE ALARM
(in operational mode only)
(in standby mode only)
" (3) button.
DAB600 / English Instruction Manual
5
(3) button.