Introduction; Device Description (Fig. 1-20); Scope Of Delivery - Scheppach BASA4 Traduction Des Instructions D'origine

1. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschine GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
We hope your new tool brings you much enjoyment
and success.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
Improper handling,
•
• Non-compliance of the operating instructions,
Repairs by third parties, not by authorized service
•
technicians,
Installation and replacement of non-original spare
•
parts,
Application other than specified,
•
A breakdown of the electrical system that occurs
•
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
We recommend:
Read through the complete text in the operating in-
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations. The operat-
ing instructions contain important information on how
to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs, re-
duce downtimes and how to increase reliability and
service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country. Keep the operating instructions pack-
age with the machine at all times and store it in a
plastic cover to protect it from dirt and moisture. Read
the instruction manual each time before operating
the machine and carefully follow its information. The
machine can only be operated by persons who were
instructed concerning the operation of the machine
and who are informed about the associated dangers.
The minimum age requirement must be complied
with. In addition to the safety requirements in these
operating instructions and your country's applicable
regulations, you should observe the generally rec-
ognized technical rules concerning the operation of
woodworking machines.
We cannot accept any liability for damage or acci-
dents which arise due to a failure to follow these in-
structions and the safety instructions.

2. Device description (Fig. 1-20)

1 Case door
Door lock (2.1 above/2.2 below)
2
Saw blade safety device
3
Saw blade guidance
4
Longitudinal limit stop
5
Tabletop
6
Frame
7
8 On/Off switch
Handle for saw blade tensioning
9
10 Adjustment handle for upper blade wheel
Motor
11
Suction connector
12
Adjustment handle for saw blade safety device
13
Table insert
14
Quick-release lever, saw belt tension
15
Quick-release lever, belt tension
16
17 Machine stand
Travel fixture
18
19 Transport handle
Quick-release lever, angle adjustment
20
Adjusting knob, angle setting, saw bench
21
Adjustment screw, angle adjustment
22
Electrical power connection
23
Tailstock holder
24
Lock nut
25
26 Thrust bearing mount
top and bottom guide rollers
27
28 Clamping lever, longitudinal alignment stop
Push stick
29
Mitre gauge
30
Guide rail
31

3. Scope of delivery

Open the packaging and remove the device carefully.
•
• Remove the packaging material as well as the
packaging and transport bracing (if available).
Check that the delivery is complete.
•
Check the device and accessory parts for trans-
•
port damage.
If possible, store the packaging until the warranty
•
period has expired.
Attention! The device and packaging materials are
not toys! Children must not be allowed to play with
plastic bags, film and small parts! There is a risk of
swallowing and suffocation!
Bandsaw
•
Saw table
•
Push stick
•
Longitudinal limit stop
•
• Fastening materials
Allen key SW 10/ 13
•
• Allen key SW 3/ SW4
Original operating instructions
•
Dust bag connector
•
Accesory Bag
•
Mitre gauge
•
4x frame feet
•
1x intermediate floor
•
• 4x foot caps
2x locating panels for handle
•
• 1x handle
1x drive fixture
•
GB 25