Before Starting The Equipment; Setting Up The Machine - EINHELL TC-BD 500 Instructions D'origine

Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

5.1 Assembling the machine (Fig. 3-8)
•
Place the base plate (1) in the desired positi-
on.
•
Fasten the pillar (2) with flange using the sup-
plied screws (3). (Fig. 3)
•
Slide the drill table (4) onto the pillar from
above (Fig. 4). Secure the drill table at the
desired height with the tightening screw (5).
•
Finally mount the complete machine head (6)
on the pillar.
Note: If possible, lift the machine head onto
the pillar together with another person.
•
Align the machine head so that it is vertical to
the base plate and secure the pre-fitted screw
a with the help of the supplied hex key (30)
(Fig. 5).
•
Screw the 3 supplied handles (9) in the hand-
le mounts. (Fig. 6)
•
Screw the clamping lever (17) in place as
shown in Fig. 7.
•
Before you fit the drill chuck (10) to the drill
chuck mount (24), check that both parts are
clean. Then insert the drill chuck into the
drill chuck mount by pressing it in firmly and
check that the chuck is secure (Fig. 8).

5.2 Setting up the machine

Before using the drill you must set it up in a statio-
nary position on a fi rm surface. Use the mounting
holes (12) in the base plate for this purpose. Make
sure that the machine is freely accessible for ope-
ration, adjustment and maintenance.
Anl_TC_BD_500_SPK13.indb 19 Anl_TC_BD_500_SPK13.indb 19
GB
Note: The fastening screws are allowed to be
tightened only to a point where they do not distort
or deform the base plate. Excessive tension can
lead to fracture.
5.3. Folding chip guard (Fig. 9-12)
•
Before fitting the chip guard (13) you must
move the drill table (4) to its lowest position
(see section 6.7 Setting the height of the drill
table).
•
Remove the fastening rail (23), the stop screw
(20) and the stop washer b (Fig. 9).
•
Push the fastening rail into the holder for the
chip guard (21) (Fig. 10).
Note: While you push the fastening rail into
the holder, the securing screw for the chip
guard (22) must point to the front as shown
in Fig. 12. Only then will you be able to fully
close the chip guard when it is in the installed
state.
•
Now re-fit the stop screw with the stop washer
b to the fastening rail (Fig. 11).
•
The height of the chip guard is infinitely adjus-
table and can be fastened using the securing
screw (22) (Fig. 12).
•
The chip guard must be flipped to the side to
enable bits to be changed.
5.4 Prior to using the machine for the fi rst
time
Ensure that the voltage of the mains supply com-
plies with the specifi cations on the rating plate.
Connect the machine only to a socket with a pro-
perly installed earthing contact. The drill is equip-
ped with a no-volt trip that is designed to protect
the operator from an undesired restart following a
drop in voltage. Should this happen, the machine
must be switched on again.
6. Operation
6.1 General information (Fig. 12)
To switch on, press the green On switch "I" (18);
the machine will then start up. To switch off , press
the red "O" button (19); the machine will then shut
down.
Take care not to overload the machine. If the
sound of the motor drops in pitch during operati-
on, it is being overloaded.
Do not overload the machine to the point where
the motor comes to a standstill. Always stand in
front of the machine during operation.
- 19 -
16.12.2020 10:04:54 16.12.2020 10:04:54