Before Starting The Equipment - EINHELL RT-ID 65/1 Mode D'emploi D'origine

Anleitung RT_ID_65_1_SPK7__ 08.07.14 07:12 Seite 14
GB
Hammer drilling in concrete (additional handle)
Vibration emission value a
2
K uncertainty = 1.5 m/s
Drilling in metal (handle)
Vibration emission value a
2
K uncertainty = 1.5 m/s
Drilling in metal (additional handle)
Vibration emission value a
2
K uncertainty = 1.5 m/s
The specified vibration value can be used to compare
the equipment with another electric power tool.
Important.
The vibration value may change depending on how
the electric equipment is used and may exceed the
specified value in exceptional circumstances.
Warning! The electric power tool generates an
electromagnetic field during operation. Under certain
circumstances this field may actively or passively
impede medical implants. To reduce the risk of
serious or fatal injuries, we recommend persons with
medical implants to consult their doctor and the
manufacturer of the medical implant prior to using the
equipment.
Residual risks
Even if you use this electric power tool in
accordance to instructions, certain residual risks
cannot be eliminated. The following hazards may
arise in connection with the equipment's
construction and layout:
1. Lung damage, if no suitable protective dust mask
is applied.
2. Damage to hearing, if no suitable ear protection is
applied.
3. Health damage caused by hand-arm vibrations, if
the equipment is used over a longer period or is
not properly guided and maintained.
The specified vibration value can be used to
recognize a prospective impairment of the
equipment's performance.
Reduce noise generation and vibration to a
minimum!
Vibration levels higher than 2.5 m/s
n
damage to the joints in your hand and arm.
Use only equipment that is in perfect condition.
n
Maintain and clean the equipment regularly.
n
Adopt your way of working to the equipment.
n
Do not overload the equipment.
n
14
2
= 12.345 m/s
h,ID
2
= 5.848 m/s
h,D
2
= 1.818 m/s
h,D
2
may cause
Have the equipment checked if necessary.
n
Switch off the equipment when not in use.
n
Wear gloves.
n

6. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate are
identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
6.1. Fitting the additional handle (Fig. 2-3/Item 8)
The additional handle (8) enables you to achieve
better stability whilst using the hammer drill. Do not
use the equipment without the additional handle.
The additional handle (8) is secured to the hammer
drill by a clamp. Turning the handle clockwise tightens
this clamp. Turning it anti-clockwise will release the
clamp.
The supplied additional handle (8) must first be
n
fitted. To do this, the clamp must be opened by
turning the handle until it is wide enough for the
additional handle to be slid over the chuck (1) and
on to the hammer drill.
After you have mounted the additional handle (8),
n
swivel it to the most comfortable working position
for yourself.
Now turn the handle in the opposite direction
n
again until the additional handle is secure.
The additional handle (8) is suitable for both left-
n
handed and right-handed users.
6.2 Storage of the drill (Figure 1 / Item 10)
The additional handle (8) is equipped with a storage
compartment for drill bits (10) where you can store
drill bits of different sizes.
Turn the storage compartment (10) anti-clockwise
n
and out of the additional handle (8).
Insert the required drill bits.
n
Mount the storage compartment (10) back on the
n
additional handle. When doing so, make sure that
the pins on the inner edge of the storage
compartment (10) fit onto the recesses in the
additional handle (8).
Secure the storage compartment by turning it
n
clockwise.