Table des Matières
Publicité
No modification or addition or repair of the PPE may be made without prior written consent from the manufacturer
nor without using their procedures.
Do not use beyond the area of use defined in the instructions for use.
The manufacturer cannot be held liable for any direct or indirect accident after a modification or use other than
that provided in this manual.
The anchoring device should be used solely for personal protective equipment against falls and not for lifting
equipment.
When the anchor is used as part of a fall arrest system, the user must be equipped with means for limiting the
maximum dynamic forces exerted on the user during a fall arrest, to a maximum of 6 kN.
Provide a safe distance from power lines or areas with an electrical hazard.
USAGE LIMITS:
Before any PPE implementation operation, set up a rescue plan to deal with any emergency that may occur during
the operation.
SHELF LIFE:
Metal products and mechanical products (self retracting fall arrest device,
sliding, work on ropes, anchors etc. ...) : Maximum duration of 20 years
from the date of manufacture (including storage and use).
The shelf life is given as an indication. The following factors can cause it
to vary greatly:
- Non-compliance with the manufacturer's instructions for transport,
storage and use
- "Aggressive" work environment: marine atmosphere, chemicals,
extreme temperatures, sharp edges...
- Particularly intensive use
- Shock or significant constraint
- Disregard for the product item's history.
Warning: these factors can cause damage invisible to the naked eye.
Warning: certain extreme conditions can shorten the shelf life by a few
days.
If in doubt, always remove the product for it to undergo either:
- a review
- destruction
The shelf life is not a substitute for periodic verification (minimum
annually) which will assess the condition of the product.
TO FIND YOUR LOCAL ANNUAL REVIEW CENTRE, VISIT
WWW.DELTAPLUS.EU.
No modification or addition or repair of the PPE may be made without
prior written consent from the manufacturer nor without using their
procedures.
Do not use beyond the area of use defined in the instructions for use.
The manufacturer cannot be held liable for any direct or indirect accident
after a modification or use other than that provided in this manual.
PERIODIC REVIEW of PPE:
An examination should be performed at least every twelve months by the manufacturer, or a competent person or
a competent organization, authorized by the manufacturer. This very important check is related to the
maintenance and efficacy of the PPE and hence the user's safety. A written document authorising reuse should be
obtained during this audit in order to reuse the PPE. This document will clarify that the user's safety is linked to
maintaining the efficiency and resistance of the equipment.
Replace the PPE if necessary.
In accordance with European regulations, the identification form must be completed prior to the first use of the
product and then updated and kept with the product as well as the manual by the user.
The legibility of the product labelling should be checked periodically.
STORAGE INSTRUCTIONS:
During transport and storage:
- keep the product in its packaging
- keep the product away from any sharp, abrasive, objects etc...
- keep the product away from sunlight, heat, flames, hot metal, oil, petroleum products, harsh chemicals, acids,
dyes, solvents, sharp edges and structures of small diameter. These items can affect the performance of the fall
arrest device.
After use, store the product in its packaging in a cool, dry, ventilated area.
INSTRUCTIONS FOR CLEANING / MAINTENANCE:
The metal parts are wiped with a cloth soaked in vaseline oil. Bleach and detergents are strictly prohibited.
B.P. 140 - ZAC de La Peyrolière
84405 APT CEDEX - FRANCE
Do not use this equipment beyond its limits.
To ensure its working condition and therefore the safety of the user, the
product should be checked systematically:
1/ visually inspect the following points:
- State of the strap or rope: no fraying, no boot cut, no visible damage at
seams, no burning and no unusual narrowing.
- Condition of the metal parts: no wear, no deformation, no corrosion or
oxidation.
- General condition: look for any possible damage due to ultraviolet
radiation and other climatic conditions.
- State of the anchoring device: its compliance to installation instructions
and recommendations,
- Condition of fasteners: tightening torques (kN) observed,
- That the general disposition of the work situation reduces the fall risk,
the drop height and the pendulum movement in the case of a fall.
- Correct operation and locking of connectors (EN362).
Specific conditions such as humidity, snow, ice, mud, dirt, paint, oil, glue,
corrosion, wear of the strap or rope, etc.. can significantly reduce the
operation of the fall arrest device.
2/ in the following cases:
- Before and during use
- if in doubt.
- in the case of contact with chemicals, solvents or fuels that could affect
operation.
- if it has been subjected to stress during a previous fall.
- at least every twelve months by the manufacturer or a competent
organization, mandated by them.
LV301 Anchorage device
13.09.2016
9/15
Publicité
Table des Matières
