EINHELL NEW GENERATION NFF 1200 Mode D'emploi page 27

Anleitung_NFF_1200_SPK7:_
7.2 Crosscut and miter saw
7.2.1 Conversion work for use as a crosscut and
miter saw
1. The saw is set up for use as a bench circular saw.
2. If necessary remove the angle and parallel stop
(see 7.3.2) and the saw blade guard (see
7.3.1/11).
3. Turn the knurled screw (Fig. 1 / Item 13) as far as
possible clockwise to move the saw blade to its
lowest position.
4. Pull the lever (Fig. 13 / Item 24) towards yourself
and carefully swing the saw over (Fig. 14-15)
Important. When you swing the saw bench, there
is a risk of suffering crush injuries to your hands
and finger. Only touch the saw bench at the front
and rear when swinging it. Do not reach between
the saw bench and the side parts. Hold the
bench securely as you swing it. Ensure that the
lever engages fully again after you have swung
the saw bench and that the bench is locked into
position.
5. Push the machine head (17) downwards using
the handle (Fig. 1 / Item 16) while pulling out the
locking pin (Fig. 16 / Item 25) for the height
adjustment and turning it clockwise through an
angle of 90°.
Important. The integral resetting springs will
automatically lift the machine head. Do not
immediately let go of the handle (Fig. 1 / Item
16) after cutting, but allow the machine head
(17) to rise slowly, applying slight
counterpressure as it does so.
6. If necessary release the retaining nut (Fig. 17 /
Item 26) for the splitter (Fig. 17 / Item 12), swing
the splitter upwards and tighten the retaining nut
again (Fig. 18).
7. Fit the chip box. First attach it to the two lugs (Fig.
19) and swing it upwards and then push the Allen
screw upwards and turn it through 90° (Fig. 20).
8. Connect a suitable dust extraction system to the
extractor port (Fig. 21 / Item 27) or fit the dust bag
(1) supplied with the machine.
9. The stop rails (Fig. 22 / Item 18) must be no
further than 5 mm from the cutting area and must
be adjusted if necessary. To do this, undo the
Allen screws, move the stop rails and then tighten
the Allen screws again (Fig. 22). The saw blade
(4) must not touch the stop rail at any point.
The stop rails are wearing parts which must be
replaced immediately if they are damaged since
otherwise they may pose a risk of injury to the
user.
14.01.2009 11:10 Uhr Seite 27
7.2.2 Safety equipment for the crosscut and
miter saw
Saw blade guard (Fig. 1 / Pos. 15)
The two-piece saw blade guard is designed to
prevent contact with the saw blade and to stop chips
being catapulted out of the machine. Both parts of the
saw blade guard must always return to their original
position automatically. When the machine head (17)
is in its upper position, the saw blade must have all-
round protection.
Lowering lock (Fig. 23)
The lowering lock prevents the machine head being
lowered accidentally. To release the lowering lock,
press the button (Fig. 23 / Item 29), pull the handle
(Fig. 23 / Item 16) forwards and lower the machine
head slowly and evenly.
Important. The integral resetting springs will
automatically lift the machine head. Do not
immediately let go of the handle (Fig. 23 / Item
16) after cutting, but allow the machine head (17)
to rise slowly, applying slight counterpressure
as it does so.
7.2.3 Operation as a crosscut and miter saw
A. Crosscut 0° and turntable 0° (Fig. 24)
Switch on the saw (see point 7.1)
Important. Place the material for sawing
firmly on the machine surface and press it
against the stop rail.
When you have switched on the saw, wait until
the saw blade (4) has reached maximum speed.
Release the lowering lock (see point 7.2.2) and
move the machine head (17) evenly through the
workpiece exerting slight pressure.
After the cutting process is finished, bring the
machine head back to its upper (home) position
and switch off the saw.
Important. The integral resetting springs will
automatically lift the machine head. Do not
let go of the handle (Fig. 23 / Item 16) after
cutting, but allow the machine head (17) to
rise slowly, applying slight counterpressure
as it does so.
B. Crosscut 0° and turntable 0°- 45° (Fig. 25 - 27)
In crosscut and miter saw mode, it is possible to
complete angle cuts to the left and right at angles of
0° - 45°.
Release the turntable (19) by undoing the locking
lever (Fig. 25 / Item 30).
Move the turntable to the required angle using the
handle (16), in other words the pointer (Fig. 26 /
Item 31) must point to the required angle on the
GB
27