Accessories; Maintenance Instructions; Lubrication; Cables - RIDGID K-50 Mode D'emploi

K-50 Drain Cleaning Machine

Accessories

Only the following RIDGID products have
WARNING
been designed to function with the K-50 Drain Cleaning
Machine. Other accessories suitable for use with other
tools may become hazardous when used on the K-50. To
prevent serious injury, use only the recommended ac-
cessories.

Cables

Catalog Model
No. No. Description
62225 C-1 25' (7.6m) w/Bulb Auger
56782 C-1IC 5 /
16
w/Bulb Auger
89400 C-21 50' (15.2m) w/Bulb Auger
62235 C-2 25' (7.6m) w/Drop Head Auger
56787 C-2IC 5 /
16
w/Drop Head Auger
89405 C-22 50' (15.2m) w/Drop Head Auger
62245 C-4 25' (7.6m) w/Male Coupling
62250 C-5 35' (10.7m) w/Bulb Auger
62260 C-6 35' (10.7m) w/Male Coupling
96037 C-6IC 35' (10.7m) w/Male Coupling
62265 C-7 7 1
62270 C-8 7 1
51317 C-9 10' (3.1m) Heavy-Duty Wind
Accessories
Catalog Model
No. No. Description
59235 A-14-6 6' Rear Guide Hose
84325 A-14-10 10' Rear Guide Hose
59270 A-18 Front Guide Hose Assembly
59210 A-10 Cable Carrier (Holds 90' C-8, C-9)
59205 A-1 Left-Hand Mitt
59295 A-2 Right-Hand Mitt
59230 A-13 Pin Key,
Adapters with Cable
Catalog Model
No. No. Description
59250 A-17-A Adapter with 25' x
w/Bulb Auger
59255 A-17-B Adapter with 35' x
w/Bulb Auger
59265 A-17-C Adapter with 35' x
w/Male Coupling
92095 A-17-D Adapter with 250' x
w/Bulb Auger
92100 A-17-E Adapter with 250' x
w/Drop Head
10
" x 25' (7.6m) Inner Core
" x 25' (7.6m) Inner Core
' (2.3m) Tight-Wind
/
2
' (2.3m) All-Purpose Wind
/
2
" Cable
5 /
8
" Cable
5 /
16
" Cable
3 /
8
" Cable
3 /
8
" Cable
5 /
16
" Cable
5 /
16
Tools for C-4, C-6, C-7, C-8, and C-9
Catalog Model
No. No.
62990 T-201
62995 T-202
63000 T-203
55457 T-225
62067 T-201A Straight Flex Auger
63065 T-217
54837 T-204
63005 T-205
63010 T-206
63015 T-207
63020 T-208
63025 T-209
63030 T-210
63035 T-211
63040 T-212
63045 T-213
63050 T-214
63055 T-215
63060 T-216
63280 T-218
63070 T-219
63080 T-220
63220 T-221
52812 T-230
52817 T-231
52822 T-232
48482 T-250
NOTE! See Ridge Tool Catalog for complete list of tools
and accessories.

Maintenance Instructions

Make sure machine is unplugged from power
source before performing maintenance or making
any adjustment.

Lubrication

Lubricate machine with grease at grease fitting (located on
jaw housing) once a week if used every day; once a
month if used less. Place a drop of oil on each of the
bearing points, thrust bearing, clutch jaws, etc., at least
once a year.
Cables
Cables should be thoroughly flushed with water to prevent
damaging effects of sediment and drain cleaning com-
pounds. Periodically lubricate cables and couplings with
RIDGID Cable Rust Inhibitor.
Ridge Tool Company
Description
Straight Auger, 5" Long
" O.D.
Bulb Auger, 1 1 /
8
", O.D.
Bulb Auger, 7 /
8
Retrieving Auger
Drop Head, 4" Long
"C" Cutter, 1"
"
"C" Cutter, 1 3 /
8
Funnel Auger, 3" Long
"
Spiral Cutter, 1 /
1
4
"
Spiral Cutter, 1 1 /
2
Spiral Cutter, 2"
Grease Cutter, 1"
"
Grease Cutter, 1 3 /
8
"
Grease Cutter, 1 3 /
4
4-Blade Cutter, 1"
"
4-Blade Cutter, 1 3 /
8
"
4-Blade Cutter, 1 3 /
4
Chain Knocker, 2"
Flue Brush, 3"
"
Flue Brush, 2 1 /
2
Flue Brush, 2"
"
Flue Brush, 1 1 /
2
H-D "C" Cutter, 2"
"
H-D "C" Cutter, 2 1 /
2
H-D "C" Cutter, 3"
Tool Set includes:
– T-203 – T-217
– T-205 – A-13
– T-210
WARNING