Ebike Ready - SQlab ERGOLUX Mode D'emploi

eBike Ready

SQlab products bearing the „eBike Ready" rating are suitable for use on pedelecs from the point of view of function, ergonomics and
operational stability (in accordance with the standards DIN EN ISO 4210 and DIN EN ISO 15194).
The SQlab Label eBike Ready refers exclusively to the use on pedelecs with pedal assistance up to 25 km/h. The eBike Ready label can
be found on the packaging, the user manual and the product page of your SQlab product
Replacing SQlab ERGOLUX
E-bikes and pedelecs with CE mark and pedal assistance up to 25 km/h are covered by the Machinery Directive, therefore components of
these bicycles may not be easily replaced or modified. In order to clarify the situation, a guideline for replacing E-bike/Pedelec 25 parts
has been jointly released by the associations Zwerad-Industrie-Verband (ZIV) and Verbund Service und Fahrrad (VSF) in cooperation with
the Zedler-Institut and the Bundesinnungs- band Fahrrad (BIV).
The guideline clearly regulates which bicycle dealers and repairers are allowed to replace parts on these vehicles and for which parts
they require approval from vehicle manufacturers or system suppliers. As such, it can be regarded as a recommended course of action.
Replacing the ERGOLUX saddles on a Pedelec25 is possible based on the recommendations of the "Guidelines for the replacement of
®
components in CE-marked e-bikes/pedelecs with pedal assistance up to 25 km/h" of the Zweirad-Industrie-Verband (ZIV) and Service
and Bicycle Association (VSF) in cooperation with the Zedler-Institut and the Bundesinnungsverband Fahrrad (BIV), provided the dis-
placement towards the rear to the series/original use area is not greater than 20 mm. A changed load distribution beyond the intended
adjustment range may cause critical steering characteristics. The length of the seat stays on the saddle frame and the saddle shape also
play a role.
On our website www.sq-lab.com/service/downloads/ in the service area under Downloads you will find a document called eBike Ready.
There you will find detailed information about the component exchange on Pedelec25, as well as the guide for the component exchange
made by the associations Zweirad-Industrie-Verband (ZIV), Verbund Service und Fahrrad (VSF), the Zedler Institute and the Bundesin-
nungsverband Fahrrad (BIV).
Replacing SQlab ERGOLUX
Component replacement of the ERGOLUX
subject to EU Directive 2002/24 / E6 or EU Regulation No. 168/2013, is possible based on the guideline " Component replacement on
S-pedelecs - fast e-bikes / pedelecs with a pedal assist up to 45 km/h" of the German Association of the German Bicycle Mechanic (BIV),
TÜV Rheinland, velotech.de, Association Service and Bicycle (VSF), Zedler- Institute and the Zweirad-Industrie-Verband (ZIV), provided
that the offset to the rear of the standard/original application area is not greater than 20 mm. A changed load distribution beyond the
intended adjustment range may cause critical steering characteristics. The length of the seat stays on the saddle frame and the saddle
shape also play a role.
On our website www.sq-lab.com/service/downloads/ in the service area under Downloads you will find a document called eBike Ready.
There you will find detailed information about the component exchange on Pedelec45, as well as the guide for the component exchange
made by the associations Zweirad-Industrie-Verband (ZIV), Verbund Service und Fahrrad (VSF), the Zedler Institute and the Bundesin-
nungsverband Fahrrad (BIV).
saddles on Pedelec25
®
saddles on Pedelec45
®
saddles on fast pedelecs, so-called S-Pedelec, which are classified as motor vehicles and are
®