Using The Analog Multi-Channel Playback Mode; Activating The Analog Multi-Channel Playback Modes - JVC RX-DP20VBK Manuel D'instructions

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Using the Analog Multi-channel Playback Mode

This receiver provides the DVD MULTI and EXT 7.1CH playback modes for reproducing the analog discrete output
mode of the DVD player or another component such as a digital decoder. Before using these playback modes, refer
also to the manual supplied for those components.
• The following operations are only possible when the receiver is ready for Zone 1 operations, and are used only
for the Zone 1 sources—"DVD MULTI" and "EXT 7.1CH."
Activating the Analog Multi-channel
Playback Modes
Perform the basic settings and adjustments using the Setup and
Adjustment Menus first (see pages 35 to 50).
Activating DVD MULTI or EXT 7.1CH playback mode
automatically recalls the memorized settings and adjustments.
• You also need to set the target component to the analog discrete
output mode.
IMPORTANT:
Check following before or while using the buttons and controls.
For Zone 1 operations:
The ZONE 1 ON/OFF lamp on the unit is lit.
• When using the unit:
– "ZONE 2" is not shown in the main display.
– Press DOOR DOWN to use the buttons inside the
front door.
To close the front door, press DOOR UP.
• When using the remote control:
– Set the ZONE 1/ZONE 2 (LEARN/TRANSMIT) selector to "ZONE 1."
– Check the indication shown on the remote's display when you
press a button on the remote control—this indicates the remote
control operation mode together with multi-room operation mode
(either ZONE 1 or ZONE 2) for a while.
LEARN
TRANSMIT
ZONE 1
ZONE 2
Ex. When you press DVD MULTI with
ZONE 1/ZONE 2 (LEARN/TRANSMIT) selector
set to "ZONE 1."
1. Press DVD MULTI or EXT 7.1 CH.
EXT 7.1CH
DVD MULTI
On the unit
(inside the front door)
Note:
To view the pictures through a component connected to the EXT
7.1CH IN jacks, you need to follow one of the methods explained
on page 12.
2. Select the analog discrete output mode on the
connected component, and start playback.
• Refer to the manual supplied with the connected component.
DOOR
DOWN
LEARN
TRANSMIT
STANDBY
ON
ZONE 1
ZONE 2
ZONE 1
ZONE 2
TV/CATV/DBS
VCR 1
ON/OFF
ON/OFF
STANDBY/ON
STANDBY/ON
ZONE 1
EXT 7.1CH
DVD MULTI
From the remote control
3. Apply the THX mode or the DSP mode if
necessary.
• Press THX to apply the THX mode.
Each time you press the button, "THX U2 CINEMA" or
"THX MUSIC" will be activated.
THX
On the unit
(inside the front door)
Note:
You cannot apply the THX mode in the following cases:
– When Analog Direct is turned on,
– When the Zone 2 speakers are activated, or
– When the surround back speakers are deactivated or only one
surround back speaker is used.
• Press DSP to apply one of the DSP modes (except
"STEREO FILM" and "MONO FILM").
Each time you press the button, the DSP modes change in
sequence (see page 58 for details).
DSP
On the unit
(inside the front door)
To adjust the speaker output level using the remote control,
see page 56.
To cancel the THX and DSP modes
Press SURR/DSP OFF.
"DSP OFF" appears on the display.
SURR/DSP
OFF
On the unit
(inside the front door)
THX
From the remote control
DSP
From the remote control
SURR/DSP
OFF
From the remote control
60

Publicité

Chapitres

Table des Matières
loading

Table des Matières