Receiving Radio Broadcasts; Tuning In To Stations Manually - JVC RX-DP20VBK Manuel D'instructions

Receiving Radio Broadcasts

You can browse through all the stations or use the preset function to go immediately to a particular station.
Indicates the functions YOU CAN ALSO USE when
the receiver is ready for Zone 2 operations.
IMPORTANT:
Check the following before or while using the buttons and controls.
For Zone 1 operations:
The ZONE 1 ON/OFF lamp on the unit is lit .
For Zone 2 operations:
The ZONE 2 ON/OFF lamp on the unit is lit.
• When using the unit:
– For the Zone 1 operations: "ZONE 2" is not shown in the main
display.
– For the Zone 2 operations: "ZONE 2" is shown in the main
display.
– Press DOOR DOWN to use the buttons inside the
front door.
To close the front door, press DOOR UP.
• When using the remote control:
When operating the receiver using the remote control, the
display on the unit always shows the Zone 1 source
information though you are operating it for the Zone 2
source.
– Set the ZONE 1/ZONE 2 (LEARN/TRANSMIT) selector to "ZONE 1"
or "ZONE 2" correctly.
– Check the indication shown on the remote's display when you
press a button—this indicates the remote control operation mode
together with multi-room operation mode (either ZONE 1 or
ZONE 2) for a while.
LEARN TRANSMIT
ZONE 2
ZONE 1
LEARN TRANSMIT
STANDBY ON
ZONE 1 ZONE 2
ZONE 1
ZONE 2 TV/CATV/DBS VCR 1
ON/OFF ON/OFF
STANDBY/ON STANDBY/ON
ZONE 1
Ex. When you press FM/AM
with ZONE 1/ZONE 2
(LEARN/TRANSMIT)
selector set to "ZONE 1."
33
DOOR
DOWN
LEARN TRANSMIT
ZONE 1 ZONE 2
LEARN TRANSMIT
STANDBY ON
ZONE 1 ZONE 2
ZONE 1 ZONE 2 TV/CATV/DBS VCR 1
ON/OFF ON/OFF
STANDBY/ON STANDBY/ON
ZONE 2
Ex. When you press FM/AM
with ZONE 1/ZONE 2
(LEARN/TRANSMIT)
selector set to "ZONE 2."

Tuning in to Stations Manually

1. Press FM/AM.
The last received station of the last selected band is tuned in.
• Each time you press the button, the band alternates
between FM and AM.
FM/AM
On the unit
(inside the front door)
When operating for Zone 1
ANALOG
L R
SUBWFR
When operating for Zone 2
2. Press TUNING 5 / ∞ (inside the front door)
or TUNING UP/DOWN until you find the
frequency you want.
DOWN UP
/ TUNING / TUNING
On the unit
(inside the front door)
Notes:
• When a station of sufficient signal strength is tuned in, the
TUNED indicator lights up on the display.
• When an FM stereo program is received, the STEREO
indicator also lights up.
• When you hold the button (and release it) in step 2, the
frequency keeps changing until a station is tuned in.
• You can only select the same station of the same band (FM or
AM) for both Zone 1 and Zone 2 operations. If you change the
station for Zone 2, it also changes for Zone 1 (and vice versa:
indications in the main display also change). This also means
that if you change the station for Zone 2 while recording a
broadcasting program in Zone 1, recording in Zone 1 will be
interrupted.
FM/AM
From the remote control
AUTO MUTING
SPEAKERS 1
VOLUME
dB dB
AUTO MUTING
SPEAKERS 1
ZONE 2
VOLUME
dB dB
/ REW PLAY
FF/
DOWN TUNING UP
From the remote control