Scheppach HM80L Traduction Á Partir De La Notice Originale page 13

• Check the power tool for damage.
• Before further use of the power tool, safety devices or
slightly damaged parts should be carefully inspected
for proper and intended function.
• Verify that the moving parts work properly and do not
jam and check that there are no damaged parts. All
parts must be installed correctly and meet all require-
ments to ensure the proper operation of the power tool.
• Damaged safety devices or other parts must be re-
paired by an authorized dealer in accordance with re-
gulations or replaced, unless otherwise specified in
the instructions.
• Damaged switches must be replaced at a service sta-
tion.
• Do not use electric tools with switches that cannot be
turned on and off.
• ATTENTION
• The use of other service tools and other accessories
can mean a risk of personal injury.
• Your power tool should be repaired by a qualified elec-
trician.
• This power tool complies with the relevant safety regu-
lations. Repairs may only be performed by a qualified
electrician, using original replacement parts, otherwise
injury to the user may occur.
Additional safety notes for miter saws
• Do not use deformed or damaged blades.
• Do not operate the saw without guards in place.
• Replace the table insert when worn.
• The saw should only be used to cut wood, wood-like
materials and plastics.
• Use only the manufacturer's recommended saw blades
that meet the EN847-1 standard.
• Attach a dust collector to your miter saw during ope-
ration.
• Select the blades according to the material to be cut.
• Check the maximum depth of cut.
• When cutting longer pieces always use extension rails
and insert clamps or other clamping devices for bet-
ter grip.
• Wear ear protection.
• The operator station is in front of the machine.
• Use the clamping device to secure the workpiece.
• Turn off the power tool if the blade gets stuck in the
workpiece or the workpiece gets wedged.
• Warning: Do not use blades made of high speed steel.
• Keep the floor area free of loose particles such as wood
chips and cuttings.
• Make sure that the blade speed indicated on its label
is at least as high as that of the saw speed.
• Use gloves when handling saw blades and rough ma-
terials.
• Be sure to use only shims and spindle rings that are
suitable for the purpose specified by the manufacturer.
• Warning: Do not remove cuttings or other parts of the
workpiece from the cutting area while the machine is
running and the saw has not yet come to a complete
stop.
• Always clamp the workpiece to the saw table.
• Make sure that the machine is sitting securely before
beginning to saw.
WArninG! noise can be harmful to your health. if a sound
level of 85dB (A) is exceeded, ear protection must be worn.
Before each use, all guards
and other parts should be carefully inspected to
see whether they still fulfill their functions.
check for alignment, smooth operation, breakage
or other damage that could impair function. A
damaged part should either be immediately and professio-
nally repaired
or replaced.
m Hazard from blocking workpieces or parts thereof!
If blockage occurs, please proceed as follows:
1. switch the device off
2. unplug it
3. Wear gloves
4. correct the blockage with appropriate tools.
Additional safety instructions for laser light
The laser light and laser radiation used in this system
comply with class 1 and a maximum performance of 390
µW and 650 nm wave length. Normally laser does not
represent an optical danger, although staring into the
beam can cause flash blinding.
Warning: Do not look directly into the laser beam, since
this could represent a risk. Please observe the following
safety instructions:
• The laser may only be used and maintained in accord-
ance with the instructions of the manufacturer.
• Only point the beam onto the work piece, and never at
a person or another object.
• The laser beam must not deliberately be pointed at
persons. It must not be pointed into the eyes of a per-
son for more than 0.25 seconds.
• Always make sure that the laser beam is directed onto
a robust work piece without a reflecting surface. That
means that timber and materials with a rough surface
are acceptable. Shiny, reflecting plates or similar ma-
terials are not suitable for laser, since the reflecting
surface could return the beam to the operator.
• Do not exchange the laser light unit for another type.
Repairs have to be conducted by the manufacturer or
an authorised specialised company.
Caution: You must only apply the regulation and adjust-
ment tools and methods described in this manual. Non-
observance can lead to dangerous radiation.
m proper use
ce tested machines meet all valid ec machine guidelines as
well as all relevent guidelines for each machine.
• The machine must only be used in technically perfect
con dition in accordance with its designated use and
the in structions set out in the operating manual, and
only by safety-conscious persons who are fully aware of
the risks involved in oerating the machine. Any func-
tional dis orders, especially those affecting the safety of
the machine, sholud terefore be rectified immediately.
• Any other use exceeds authorization. The manufacturer
13