Safety Regulations; Layout And Items Supplied; Proper Use - EINHELL CC-PO 1100/1 E Instructions D'origine

Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.

1. Safety regulations

The corresponding safety information can be
found in the enclosed booklet.
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.

2. Layout and items supplied

2.1 Layout (Fig. 1)
1. Spindle lock
2. Front grip
3. ON/OFF switch
4. Speed control
5. Rear grip
6. Power cord
7. Polishing / sanding disk
8. Speed indicator
2.2 Items supplied (Fig. 2)
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any pa-
ckaging and/or transportation braces
(if available).
Anl_CC_PO_1100_1_E_SPK9.indb 16 Anl_CC_PO_1100_1_E_SPK9.indb 16
GB
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suff ocating!
1. Storage case
2. Sanding and polishing machine
3. Additional handle
4. Polishing / sanding disk
5. Foamed plastic attachment
6. Synthetic polishing attachment
7. Sanding attachment K = 60 (2 pcs)
8. Sanding attachment K = 80 (2 pcs)
9. Sanding attachment K = 120 (2 pcs)
10. Hex wrench 8 mm
11. Hexagon socket screw M 10 x 20 mm (2 pcs)
•
Original operating instructions
•
Safety instructions

3. Proper use

The machine is designed for polishing coated
surfaces and for sanding wood, plastic and si-
milar materials using the appropriate abrasive
paper. The abrasive paper which is included with
the product is for sanding wood.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Improper use
All applications with the device which are not sta-
ted in the chapter "Intended use" are deemed to
be contrary to the intended use.
The device must not be used for the following
purposes:
•
Work on lightweight partition walls (drywalls)
and other surfaces containing plaster, ce-
ment, foam, mineral fiber and silicate.
•
Work on metals involving the generation of
metal dust.
•
Working on coatings containing lead and
working on types of wood and metal which
- 16 -
13.02.2020 09:53:29 13.02.2020 09:53:29