Introduction; Device Description - Scheppach HBS30 Traduction Des Instructions D'origine

1. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
we hope your new tool brings you much enjoyment
and success.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
We recommend:
Read through the complete text in the operating in-
structions before installing and commissioning the
device.
The operating instructions are intended to help the
user to become familiar with the machine and take
advantage of its application possibilities in accord-
ance with the recommendations.
The operating instructions contain important informa-
tion on how to operate the machine safely, profes-
sionally and economically, how to avoid danger, cost-
ly repairs, reduce downtimes and how to increase
reliability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country.
Keep the operating instructions package with the
machine at all times and store it in a plastic cover to
protect it from dirt and moisture. Read the instruction
manual each time before operating the machine and
carefully follow its information.
The machine can only be operated by persons who
were instructed concerning the operation of the ma-
chine and who are informed about the associated
dangers. The minimum age requirement must be
complied with.
In addition to the safety requirements in these operat-
ing instructions and your country's applicable regula-
tions, you should observe the generally recognized
technical rules concerning the operation of wood-
working machines.
We accept no liability for damage or accidents which
arise due to non-observance of these instructions
and the safety information.
2. Device description (Fig. 1- 1b)
1 Clamping screw
2 Top saw band roller
3 Rubber surface
4 Saw band guard
5 Top saw band guide
6 Table insert
7 Saw table
8 Table enlargement
9. Bottom saw band roller
10 Clamping lever
11 Foot
12 Cover locking mechanism
13 Side cover
14 Parallel stop
15 On/off switch
16 Locking screw for top saw band roller
17 Set screw for top saw band roller
18 Machine frame
19 Mains cable
20 Motor
21 Wing nut
22 Locking handle for saw table
23 Clamping plate
24 Extraction nozzle
25 Mitre gauge (optional)
26 Saw band
27 Adjustment handle for saw band guide
28 Locking handle for saw band guide
29 Push stick
30 Allen key 5mm
31 Allen key 4mm
32 Allen key 3mm
33 Screwdriver
34 Open-ended spanner SW10/13
35 Degree scale for swivel range
36 Screw M6x35
37 Flat washer M6
38 Nut M6
39 Screw M5x7
40 Serrated washer M5
41 Knurled nut for parallel stop
42 Clamping lever for parallel stop
43 Guide rail for parallel stop
44 Inspection glass
45 Allen screw for top support bearing
46 Top support bearing
47 Top guide pin
48 Allen screw for top guide pins
49 Retainer (top)
50 Allen screw top retainer (2x)
51 Allen screw bottom support bearing
52 Bottom support bearing
53 Screw bottom retainer
54 Saw band protection
55 Allen screw for bottom guide pins
56 Bottom guide pin
57 Retainer (bottom)
58 Screw (saw table adjustment)
59 Nut (saw table adjustment)
60 Push Stick retainer
GB 23