Intended Use; Assembly And Adjustments; Speed Control - DeWalt DCE591 Guide D'utilisation

English
also charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Storage Recommendations
1. The best storage place is one that is cool and dry, away
from direct sunlight and excess heat or cold.
2. For long storage, it is recommended to store a fully
charged battery pack in a cool dry place out of the
charger for optimal results.
nOTE: Battery packs should not be stored completely
depleted of charge. The battery pack will need to be
recharged before use.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
COMPONENTS (FIG. A)

WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.

INTENDED USE

Your adhesive dispenser is designed for professional
concrete construction applications.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
Your adhesive dispenser is a professional power tool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Inserting a Cartridge (Fig. D)
1. Rotate the speed control dial to the OFF position.
2. Open clutch lever 4 to allow movement of racks
Fig. D
3
8
7 .
7
5
4
3. Retract the rack by pulling the rack handle
the tool.
nOTE: If using cartridge designed for a mixing nozzle
to be attached before loading into dispenser, screw the
static mix nozzle onto the cartridge before proceeding
to step 3.
4. Insert cartridge.
5. Line up the cartridge and the cartridge nozzle opening
to assure correct positioning.
6. Push rack handle forward, lining up pistons
openings on the cartridge.
7. Remove caps and plugs on the dispensing end of
cartridge.
nOTE: If using cartridge designed to be loaded into
dispenser before mixing nozzle is attached, screw the
static mix nozzle onto the cartridge.
Adjusting/Setting the Material Dosage
and Rate of Flow (Fig. E)
specifications
Max Speed*: 6-1/8" per minute
Minimum Speed*: ¼" per minute
Max Dose*: 28 - 32 seconds
Min Dose*: 2-5 seconds
* Specifications are estimates and can vary depending upon the tool,
temperature and adhesive type.
Dose Control
The dose control dial 3 is used to set the dosage/amount
of adhesive dispensed per trigger pull.
• To set the dosage, rotate the dosing control dial until
the amount of adhesive needed per trigger
is discharged. Keep trigger depressed while applying
adhesive. Dose control will stop the tool automatically.

Speed Control

The speed feature allows you to speed up or slow down the
rate of flow of adhesive.
• To set the rate of flow, rotate the speed control dial
to the flow that is best suited to the application.
Changing the speed while using the dosing feature will
reduce or increase the amount of adhesive dispensed.
nOTE: Both the dose control and speed control dials will act
as an "off" switch when adjusted to their minimum setting.
The tool will not function and the racks will not move when
in this state from either dial.
Fig. E
2
O
5 away from

I
(

6 with the
n
f
F
T
b
i
t
T
b
h
s
1 pull
P


2
P
a
s
F
3
D