Warnings - Dräger Polytron 8000 Serie Notice D'utilisation

en |
Troubleshooting
Fault Cause
number
002, Serious data error
025 - 027, in the instrument,
030 - 034, various causes.
041, 042,
044, 050,
052, 081,
085
010 4 to 20 mA inter-
face cable not con-
nected.
045 Instrument not
detecting any sen-
sor.
051, 054 Faulty zero calibra-
tion.
055 Faulty span cali-
bration.
076, Instrument fault.
080 - 084
090 Sensor lock func-
tion is activated. A
sensor with a dif-
ferent part number
has been con-
nected.
105 Instrument fault.
137, 64, Instrument fault.
91
®
Polytron 87x0 IR-specific:
Fault Cause
number
064, 071 Communication
fault.
083 PIR 7x00 optics
dirty.
086 Supply voltage out-
side range
087 4 to 20 mA fault at
PIR 7x00 sensor.
094, 095 Data error in the
instrument.
22
Remedy
Reset the instrument to fac-
tory default settings. If this
fault occurs again: Have
the instrument checked by
DrägerService.
Check the 4 to 20 mA inter-
face connection.
If operated as a stand-
alone instrument without a
central controller, wire pin 3
to pin 4.
Check connections.If this
fault occurs again: Have
the instrument checked by
DrägerService.
Perform zero calibration.
Perform span calibration
Check electrical connec-
tions.If this fault occurs
again: Have the instrument
checked by DrägerService.
Use a sensor with the same
part number or disable the
sensor lock function.
Have the instrument
checked by DrägerService.
Cycle power.If this fault
occurs again: Have the
instrument checked by
DrägerService.
Remedy
Check connection to PIR
7x00.
Clean PIR 7x00 optics.
Check supply voltage.
Check 4 to 20 mA connec-
tion to PIR 7x00.
Reset the sensor to factory
default settings. If this fault
occurs again: Have the
instrument checked by
DrägerService.
Fault Cause
number
096 SIL password does
not match with PIR
7x00.

10.2 Warnings

Warning Cause
number
011 Supply voltage is
out of range.
101 Data logger in
Stack mode is 100
% full and is not
logging any more
data.
102 Data logger in
Stack mode is 90 %
full.
103, 106 Data error in the
instrument. Some
dongle functions
like data logger,
sensor test, etc.
may no longer be
available.
104 Date or time setting
not valid.
105 Instrument fault.
107 Battery for data
memory empty.
110, 111, SW dongle has
112 been removed
without being deac-
tivated.
113 Alarms inhibited.
164, 165 Sensor warm-up
phase has not
ended. Increased
measurement error
must be expected.
167, 170 Calibration interval
expired.
1) Negative reading.
171
Value below range
minimum.
Low EC sensor
1)
163
vitality
®
1) Polytron 8100 EC only
Instructions for use
Remedy
Enter password again.
Remedy
Check supply voltage.
Have the instrument
checked by DrägerService.
Download the data as soon
as possible and clear the
data logger.
Reset the instrument to fac-
tory default settings. If this
error occurs again: Have
the instrument checked by
DrägerService.
Set date and time.
Have the instrument
checked by DrägerService.
Have the instrument
checked by DrägerService.
Deactivate SW dongle.
Enable alarms
Wait until the sensor has
warmed up. Do not calibrate
before sensor is fully
warmed-up.
Recalibrate the instrument.
Recalibrate zero point.
Replace sensor
®
|
Dräger Polytron 8000 Series