JVC KD-R980BTS Manuel D'instructions page 26

AUDIO SETTINGS
EQ SETTING
PRESET EQ Select a preset equalizer suitable to the music genre.
• Select [USER] to use the settings made in [EASY EQ] or [PRO EQ].
FLAT/DRVN 3/DRVN 2/DRVN 1/HARD ROCK/HIP HOP/JAZZ/POP/
R&B/USER/CLASSICAL
EASY EQ Adjust your own sound settings. The settings are stored to [USER].
• The settings made may affect the current settings of [PRO EQ].
SUB.W SP * *
1 2
:
SUB.W * 1 * 3
:
BASS:
MID:
TRE:
PRO EQ Adjust your own sound settings. The settings are stored to [USER].
• The settings made may affect the current settings of [EASY EQ].
62.5HZ
LEVEL –09 to LEVEL +09 (LEVEL 00): Adjusts the level to memorize for each source.
(Before making an adjustment, select the source you want to adjust.)
ON: Turns on the extended bass. ; OFF: Cancels.
100HZ/160HZ/250HZ/400HZ/630HZ/1KHZ/1.6KHZ/2.5KHZ/4KHZ/6.3KHZ/10KHZ/
16kHZ
LEVEL –09 to LEVEL +09 (LEVEL 00): Adjusts the level to memorize for each source.
(Before making an adjustment, select the source you want to adjust.)
Q FACTOR 1.35/1.50/2.00: Adjust the quality factor.
AUDIO CONTROL
BASS BOOST LEVEL +01 to LEVEL +05: Selects your preferred bass boost level. ;
OFF: Cancels.
LOUDNESS LEVEL 01/LEVEL 02: Boosts low or high frequencies to produce a well-
balanced sound at low volume. ; OFF: Cancels.
22
ENGLISH
00 to +06 (Default: 03
–50 to +10
LVL –09 to LVL +09
LVL –09 to LVL +09
LVL –09 to LVL +09
Default: XX
SUB.W LEVEL * 1
SUBWOOFER
SET * 3
00
00
FADER
00
00)
BALANCE * 4
VOLUME ADJUST
AMP GAIN
SPK/PRE OUT
SPEAKER SIZE
X ' OVER
SPK-OUT * 2
(Not applicable when 3-way crossover is selected.)
SUB.W 00 to SUB.W +06 (SUB.W +03): Adjusts the
output level of the subwoofer connected via speaker
lead. ( 35)
PRE-OUT * 3
SUB.W –50 to SUB.W +10 (SUB.W 00): Adjusts
the output level of the subwoofer connected to the
lineout terminals (SW or REAR/SW) through an external
amplifier. ( 35)
ON: Turns on the subwoofer output. ; OFF: Cancels.
(Not applicable when 3-way crossover is selected.)
POSITION R15 to POSITION F15 (POSITION 00): Adjusts the front
and rear speaker output balance.
POSITION L15 to POSITION R15 (POSITION 00): Adjusts the left and
right speaker output balance.
LEVEL –15 to LEVEL +06 (LEVEL 00): Preset the initial volume level
of each source (compared to the FM volume level). Before adjustment,
select the source you want to adjust.
LOW POWER: Limits the maximum volume level to 25. (Select if
the maximum power of each speaker is less than 50 W to prevent
damaging the speakers.) ; HIGH POWER: The maximum volume level
is 35.
(Not applicable when 3-way crossover is selected.)
Depending on the speaker connection method, select the appropriate
setting to get the desired output. ( 24, Speaker output settings)
Depending on the crossover type you have selected
(see [X ' OVER TYPE] below), 2-way crossover or
3-way crossover setting items will be shown. ( 24,
Crossover settings)
By default, 2-way crossover type is selected.