Initial Operation - WMF Lumero Multi-kettle Mode D'emploi

▪ Take the pot off the base to fill.
▪ Only fill the glass kettle (8) with clean water, not milk, coffee, etc.
▪ Do not move the appliance or pull on the mains cable during operation.
▪ WARNING: Danger of scalding due to hot casing and escaping steam. Only hold the kettle by
the handle when in operation, and do not open the lid when pouring.
▪ Always empty the glass kettle (8) completely. Do not leave residual water in the appliance for a
long period of time.
▪ Pull the mains plug:
⋅ if the appliance malfunctions during use;
⋅ before cleaning and care;
⋅ after use.
▪ No liability shall be accepted for any damage resulting from misuse, incorrect operation or
improper repairs.
Warranty claims shall likewise be excluded in such cases.
▪ Packaging materials, such as plastic bags, must be kept out of the reach of children.
▪ WARNING: Do not let hard objects (e.g. glasses, spoons, etc.) fall in the glass insert! Do not subject
the glass insert or lid to sudden temperature changes (e.g. from the refrigerator or freezer in boil-
ing water) – gradually warm or cool the glass insert in 20–30°C steps!
LED lighting:
The LED lighting in the base is a status indicator.

Initial operation

The kettle is made from stainless steel and WMF glass. This is heat resistant, stable, neutral tasting
and easy to clean. Thoroughly clean the inside of the kettle before using it for the first time. (See the
chapter "Cleaning and care").
The unused length of the connecting cable can be wound at the bottom of the base. Connect the
mains plug to an earthed socket.
Add the desired amount of water (min. 500 ml, max. 1,600 ml). Note: If the kettle is not filled with
enough water, the overheating protection automatically switches off the heating elements. The
appliance must be left to cool. Too much water may cause boiling or hot water to overflow, which can
cause serious injury or burns.
The lid (2) must be firmly secured to prevent splashes. Place the kettle on the base in any position. Do
not use the water from the first boiling process for food preparation.
Note: The kettle has a 360° spout.
The following functions are available:
Setting the temperature unit (°C/°F)
1. Connect the appliance to the mains.
2. Press the increase temperature button (13) and hold it down for at least 3 seconds.
3. The current temperature unit blinks in the display.
4. Select °C or °F with the increase temperature button (13).
5. Confirm your choice by pressing the start/stop button (21) or cancel by pressing the on/off button
(11).
18
Boiling water
1. Fill the kettle with the desired amount of water (min. 500 ml, max. 1,600 ml).
2. Place the lid (2) on the kettle (8).
3. Put the kettle on the base (10) in any position.
4. Press the on/off button (11). The water boil program button (20) blinks.
5. Press the start/stop button (21) to start heating. You can stop the boil cycle at any time by pressing
the start/stop (21) or on/off (11) button or lifting the kettle (8).
6. The appliance turns itself off automatically as soon as the water boils.
Making tea
1. Fill the tea strainer (4) and follow the instructions on the packaging when portioning out the tea.
As a rough guide, there should be one teaspoon of loose tea for each 250 ml of water.
2. Fill the kettle with the desired amount of water. Do not fill past the tea mark
3. Put the kettle on the base (10).
4. Put the tea strainer (4) in the kettle by inserting the tea strainer holder (3) through the lid and
locking into the cap (1) (Fig. B).
5. Make sure the tea strainer (4) is flush with the lid. To do this, pull the tea strainer (4) upwards by
the tea strainer holder (3) (Fig. C).
6. Use the tea program (15) to set the desired temperature (13, 14) and brew time (18, 19).
7. Press the start/stop button (21) to start heating.
8. As soon as the desired temperature has been reached, an acoustic signal sounds and the selected
brew time flashes in the display. The tea strainer (4) can now be pressed down into the water and
the brew time started by pressing the start/stop button (21).
9. Leave the tea to steep for the appropriate amount of time depending on the type of tea. Once the
time has elapsed, the appliance beeps and the kettle switches off automatically.
10. Remove the tea strainer (4) by the cap (1).
Warning: Rising steam can cause burns and the tea strainer (4) and tea strainer holder (3) may be
hot.
Types of tea
The temperature of the water and the length of time you leave the tea to steep plays a key role in
making tea. The overview below can be used as a guide: The temperature and steeping time can be
adapted depending on the type of tea and your personal preferences.
Temperature Type of tea
Japanese green tea
60°C
White tea
70°C
Yellow tea
Green tea
80°C
Oolong tea
Black tea
90-100°C
Herbal tea, fruit tea
.
Infusion time
3-4 mins.
3-4 mins.
1-3 mins.
3-4 mins.
1-2 mins.
3-4 mins.
5-8 mins.
19