Before Starting The Equipment - EINHELL TC-MS 2513 T Instructions D'origine

For use as a bench-type saw:
Saw bench ..................................... 416 x 352 mm
Cutting depth .................................... max. 40 mm
Maximum cross-section
of the workpiece ............................. 15.5 x 40 mm
Minimum size
of the workpiece ..................... 30 x 10 x 100 mm
Parallel stop ....Can be pivoted from -45° to + 45°
For use as a crosscut saw:
Swiveling range............................. -45° / 0° / +45°
Miter cut .................................. 0° to 45° to the left
Saw width at 90° .............................. 130 x 75 mm
Saw width at 45° .............................. 120 x 50 mm
Saw width at 2 x 45°
(double miter cut) ............................... 70 x 35 mm
Minimum size
of the workpiece ..................... 50 x 10 x 100 mm
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
L sound pressure level ........................ 93 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ........................ 106 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 61029.
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Anl_TC_MS_2513_T_SPK1.indb 24 Anl_TC_MS_2513_T_SPK1.indb 24
= 2.02 m/s
2
h
2
- 24 -
GB
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
•
The machine has to be set up in a stable po-
sition, i.e. it has to be bolted to a workbench,
a universal stand or the like.
•
All the covers and safety devices have to be
properly fitted before the machine is switched
on.
•
It must be possible for the saw blade to run
freely.
•
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted and
that the machine's moving parts run smoothly.
•
Before you connect the machine to the power
supply, make sure the data on the rating plate
13.10.15 13:26 13.10.15 13:26