Other Displays; Before Each Use - Dri-Eaz Evolution LGR F292-A Guide D'utilisation

How to change the language display
CAUTION: While in the change-language mode,
pressing other keys can change the programming of the
machine. Do NOT press other keys you're not instructed
to press.
Use the DISPLAY key to change the display language.
Follow these steps:
1. Unplug the unit.
2. While holding down the DISPLAY key, plug the unit in.
The display reads ENGLISH.
3. To change to FRANCAIS, DEUTSCH, or ESPANOL,
press the DISPLAY key or the CLEAR key.
4. When the desired language is shown in the display,
unplug the unit, and the language is set.
CLEAR. Press the CLEAR key to reset the JOB
HOURS
1. As the display cycles between DEHUMIDIFIER ON,
JOB HOURS, and TOTAL HOURS, press the DISPLAY
key when JOB HOURS appears on the screen. That will
make the display read JOB HOURS steadily.
2. Then press the CLEAR key to re-set the numerals to
00000.
3. Press DISPLAY again to re-start the display cycle.
NOTE: the TOTAL HOURS reading cannot be re-set.
PURGE. Press the PURGE key to empty water
from the pump reservoir. During normal operation, the
pump purges automatically every six minutes, or
whenever the reservoir is full. The display will read
PUMP PURGING with a numeral countdown. To purge
the pump manually:
1. Turn the power off using the OFF key, and let the unit
sit plugged in for about 10 minutes. This allows water to
drip from the coils.
2. Press PURGE to remove residual water.

Other Displays

Defrost cycle
During normal operation, frost may form on the coils.
When this occurs, a temperature sensor detects the frost
and initiates a defrost cycle. The display will read
DEFROST ON. Dehumidification stops during the
defrost cycle. When the unit completes the cycle, the
display returns to DEHUMIDIFIER ON, and normal
dehumidification resumes.
Error messages
If the onboard diagnostics discover a problem, the unit
will display "GET SERVICE," followed by "ER" and a
07-01480C 2010-01
numeral from 01 to 09. If this message appears, first
follow these steps:
1. Unplug the unit and then plug it back in. This may re-
set the electronics.
2. If the error message reappears, try the solution (if one
is listed) in the "Error Messages," p. 5.
3. If the error message still appears, please contact the
Dri-Eaz Service Department at 800-932-3030.
At the end of the job
As with all dehumidifiers, once the drying job is
completed, it is important to make sure the unit is
completely purged of water before moving it. To ensure
that all water has drained into the pump, turn the
unit off, allow it to rest for 10 minutes, then press the
PURGE button. (The unit must be plugged in for the
purge to operate.) Once the purge cycle is complete,
unplug the unit and remove it promptly from the job.
MAINTENANCE
WARNING! ELECTRIC SHOCK HAZARD. Unplug
the unit before performing any maintenance. Never
use a water hose or pressure washer to clean coils,
as water entering the electrical compartment could
cause a shock hazard.

Before each use

Inspect the electrical cord for damage. Look for
fraying, cuts, etc. Do not use the unit if you find any
damage. Visit www.drieaz.com for the nearest Service
Center or call 800-932-3030.
Inspect and vacuum filter as needed. Keep a clean
filter in the unit at all times to protect internal
components from dust and other particulate build-up.
The Evolution is equipped with a 3M™ High Air-Flow
filter. The HAF filter may be vacuumed clean and reused
up to three times. Do not rinse or wash the HAF filter,
as it will reduce the effectiveness of the electrostatic
material.
Replace only with a new 3M HAF Filter (Dri-Eaz part no.
F372). For parts and service call your local distributor or
contact the Dri-Eaz Service Department at
800-932-3030.
CAUTION: Dust can cause the unit to overheat and
shut down. Do not operate when excessive dust or
airborne particles are present, such as during
sanding or spray-painting. Inspect and clean air filter
elements and coils frequently.
IMPORTANT: Replace the HAF filter whenever 1)
it has been vacuumed clean 3 times or 2) it has
been used on a mold remediation job or
otherwise exposed to potentially dangerous
contaminants.
4 Dri-Eaz Products, Inc.