Internal Battery - Milwaukee M18 Manuel De L'utilisateur

Attaching the Remote Dash Mount
To reduce the risk of serious injury
WARNING
or death, install the remote dash
mount away from vehicle functions and safety
features, such as air bags. Air bag deployment
could cause the remote to become a projectile.
Make sure the surface is clean and dry before at-
taching.
To attach, peel the protective layer from the back
of the remote dash mount. Place the mount on the
desired surface. Let the mount cure for 24 hours
before removing the remote from mount.
ONE-KEY™
To learn more about the ONE-KEY™ functionality
for this tool, go to milwaukeetool.com/One-Key. To
download the ONE-KEY™ app, visit the App Store or
Google Play from your smart device.
ONE-KEY™ Indicator
Solid Blue Wireless mode is active and ready
to be configured via the ONE-KEY™
app.
Blinking Blue Tool is actively communicating with
the ONE-KEY™ app.
Blinking Red Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
OPERATION
To reduce the risk of injury, do not
WARNING
look directly into the light when the
light is ON.
To turn ON the light, press the Power button
To turn OFF the light, press the Power button again
To turn ON the remote, turn the Remote on/off
switch ON.
Press the MODE button to cycle through spot, flood
low, and flood high light settings.
To rotate the light, use the remote joystick
To adjust the speed of rotation, click down on the
remote joystick .
To return the light to the home position, press and
hold the remote home button
MAINTENANCE
To reduce the risk of injury, always
WARNING
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
lithium button/coin cell battery. A new
or used battery can cause severe in-
ternal burns and lead to death in as
little as 2 hours if swallowed or enters the body.
Always secure the battery cover. If it does not
close securely, stop using the device, remove the
batteries, and keep it away from children. If you
think batteries may have been swallowed or en-
tered the body, seek immediate medical attention.
An internal battery is used to facilitate full ONE-KEY™
functionality. The internal battery is located on the
bottom of the light head.
To replace the battery:
1. Remove the light head from the base.
2. Remove the screw and open the battery door.
3. Remove the old battery, keep it away from children,
4. Insert the new battery (3V CR2032), with the posi-
5. Close the battery door and tighten the screw
1. Attach the light head to a base
2. Remove the four screws
.
3. Press and hold the pairing
.
.
4. Reinsert the left rotation
for two seconds.
1. On the remote's backside, unscrew the single
2. Replace with AAA batteries.
3. Place the battery lid back onto remote and screw
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
Clean dust and debris from any vents. Keep tool
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around tools.
For repairs, return the tool, battery pack and charger
to the nearest authorized service center.
5
ONE-KEY™
Chemical Burn Hazard.
WARNING
This device contains a

Internal Battery

and dispose of it properly.
tive side facing up.
securely.
Pairing a New Remote
that is connected to power.
Do not turn on light.
on the left rotation plate of
the light head. Remove the
plate from the light head.
button on the light head.
Turn on the remote and
push up on the remote joy-
stick and hold. Once paired,
the light will blink three
times. The new remote is
now connected.
plate to the light head using
the four screws.
Changing the Remote Batteries
screw and lift the battery lid to expose the batteries.
securely.
To reduce the risk of personal in-
WARNING
jury and damage, never immerse
Cleaning
Repairs
Left rotation plate
Pairing button