Milwaukee M18 Manuel De L'utilisateur page 3

BATTERY TOOL USE AND CARE
• Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
• Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal
to another. Shorting the battery terminals together
may cause burns or a fire.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact ac-
cidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
• Do not use a battery pack or tool that is dam-
aged or modified. Damaged or modified batteries
may exhibit unpredictable behavior resulting in fire,
explosion or risk of injury.
• Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or tem-
perature above 265°F (130°C) may cause explosion.
• Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions. Charging
improperly or at temperatures outside the specified
range may damage the battery and increase the risk
of fire.
SERVICE
• Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
• Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SPECIFIC SAFETY RULES FOR
SEARCH LIGHT
• Do not use magnet for horizontal overhead
mounting.
• This light should not be illuminated while driv-
ing on public roads except when authorized for
emergency situations. Check local motor vehicle
and traffic regulations for your area of operation.
• Always use common sense and be cautious when
using tools. It is not possible to anticipate every
situation that could result in a dangerous outcome.
Do not use this tool if you do not understand these
operating instructions or you feel the work is beyond
your capability; contact Milwaukee Tool or a trained
professional for additional information or training.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
Federal Communications Commission
WARNING: Changes or modifications to this unit
not expressly approved by the party responsible for
compliance could void the user's authority to operate
the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found
to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated
in a commercial environment. This equipment gener-
ates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instruction manual, may cause harmful interference
to radio communications. Operation of this equip-
ment in a residential area is likely to cause harmful
interference in which case the user will be required
to correct the interference at his own expense.
Canadian RSS-210
This device complies with RSS-210 of the Industry
Canada Rules. Operation is subject to the following
conditions:
1) this device may not cause interference and
2) this device must accept any interference, including
interference that may cause undesired operation
of the device.
SPECIFICATIONS
Cat. No. ..................................................... 2123-20
Ingress Protection............................................ IP56
Recommended Ambient
Operating Temperature ......................0°F to 125°F
M18™ Portable Base .......................... 49-16-2123
Battery Type .................................................M18™
Charger Type................................................M18™
DC Input Volts.................................................. 18 V
Max DC Input Amps............................................3.0
12V DC Permanent Base ..................49-16-2123P
DC Input Volts.................................................. 12 V
Max DC Input Amps............................................5.0
Remote ..............................................49-16-2123R
Battery Type......................................................AAA
DC Input Volts..................................................1.5 V
SYMBOLOGY
Volts
Direct Current
Read operator's manual
CAUTION
Federal Communications
Commission
UL Listing for Canada and U.S.
C US
3
Do not stare at
operating light source