Oscartielle GENIUS G.I. H125 Mode D'emploi page 25

- Check that the unit isn't close to strong air flows or heat sources (see point 4).
- Check that the unit is levelled and that the environmental conditions meet those indicated in point 4.
If the problem persists despite the above checks, contact your nearest service centre.
Warning: Never approach the motor compartment in the event of leaking gas or a fire. Unplug at the mains. Never use
water to put out any flames, but only dry powder extinguishers.
13 – Accessories
The GENIUS displays can be fitted with the following accessories on request.
- Night cover.
- Row dividers.
- Raised plexiglas edges for display shelves.
- Shelf illumination.
- Electric defrosting (armoured resistances on the evaporator).
If interested in purchasing any of the above accessories, contact your nearest Oscartielle dealer or Oscartielle S.p.A
directly. Only Oscartielle Customer Service is allowed to fit the defrosting resistances.
14 - Customer service
If you need the assistance of a technician or mechanical, electrical or compressor components need to be replaced,
please contact the dealer from whom you bought the unit and ask for original spare parts.
15 - Dismantling and elimination of cabinet
For environmental reasons and in compliance with the regulations in your country, separate the parts of the cabinet for
disposal and/or recycling.
All the parts that make up the cabinet are made of materials that are not classifiable as urban waste except for the
metallic parts that are not classified as special waste in most countries. As regards the parts of the refrigeration circuit,
that is the refrigerating gas and lubricating oil, these should not be disposed of carelessly and can be recycled by
specialized centers.
The gas contained in foam polystyrene for thermal insulation of the cabinet is (CO
This product contains HFC, namely fluoridated gasses, a refrigerating gas with a high Global Warming Potential
(GWP) regulated by the Kyoto protocol.
The gas contained in foam polystyrene for thermal insulation of the cabinet is (R134A).
Oscartielle equips its plug-in cabinets with the following types of refrigerating gasses:
R 290; GWP = 3
(100)
R 134a; GWP = 1300
(100)
R 452A; GWP = 2140
(100)
R 404A; GWP = 3750
(100)
This unit is hermetically sealed and the refrigerating gas load is under 3 kg.
For this reason it is not subject to the requisite of an installation booklet and periodic inspections for leakage of
the refrigerating gas (presidential Decree no. 147 of February 15th 2006, Art. 3 and 4).
16 - Manufacturer's statement (Start-up prohibition)
The above models are also built to be assembled in-line with other items of machinery to produce a machine, as defined
by Directive 2006/42/CE.
Therefore, the Manufacturer hereby states that it is not permitted to start the unit up until the machine in which it is
incorporated or will become a part of has been identified and its compliance with the provisions of Directive 2006/42/CE
and applicable national laws has been stated. In other words, until the machine referred to in this statement becomes one
with the final machine.
17 – Multiplexing instruction
Multiplexing instruction Genius line-up (FIG. 17)
1. The side adjusting profiles item no. 670443 and the holders for the top canopy item no. 670949 are already mounted.
2. Remove the top canopies, the bumper rail and the front decoration trim.
3. Align the multidecks and level them by adjusting the feet.
4. Join the cabinets using the fitting screws and die-cast brackets.
5. Insert the item no. 670446 inside the canopies, in order to keep them aligned.
6. Assemble the top canopies.
Multiplexing instruction island Genius standard (FIG. 18)
- Align the multidecks and level them by adjusting the feet.
- Assemble the profile of the top decoration trim in the header cabinet, as per Ref. No. 1.
- Join the cabinets (Ref. No. 2), align the basin of the cabinets to the back part of the header.
- Assemble the top canopy as per Ref. No. 3.
- Remove the back panel (Ref. No. 6) and screw the screws in the uprights as per Ref. No. 7.
- Position the profiles that close the bottom trim (ref. No. 5)
- Assemble the top grid between the cabinets, as per Ref. No. 8.
Multiplexing instruction island Genius standard (FIG. 19)
- Align the multidecks and level them by adjusting the feet.
).
2
23