Numark MIX DECK Guide D'utilisation Rapide page 12

Tips For Using USB Devices With Your MIXDECK
•
When disconnecting a USB device from the MIXDECK, always make sure to use the SOURCE button to switch to
CD/MP3 Mode before disconnecting. Make sure that the letters "HD" are not blinking on the display when disconnecting
a USB device.
•
Disconnecting a USB device while the MIXDECK is in USB MASTER Mode could possibly cause data on the USB
device to become corrupted and unreadable.
•
Note: There is a limit of 999 songs per folder or playlist. Use multiple folders or playlists to separate large numbers of
songs.
•
We do not recommend using MP3 files over 300MB as this may affect the performace of the MIXDECK.
•
For large capacity HD, the MIXDECK can read a maximum of 9 disc partitions. Each partition is limited to 999 folders,
and each folder is limited to 999 songs.
USB MIDI MODE
You can also connect the MIXDECK to a computer via USB to use the
MIXDECK's CD decks as controllers for software programs that are
compliant with USB MIDI protocol.
manufacturer to find out if your software supports a USB MIDI controller.
Note: The mixer and iPod controls do not have any MIDI function.
To activate USB MIDI mode, connect a USB cable from the MIXDECK USB SLAVE connector to a USB port on your computer.
Then press SOURCE and turn the parameter knob to select "USB-MIDI."
MIXDECK FIRMWARE / SOFTWARE
MIXDECK works best with the latest firmware and software installed. We strongly recommend that you check for updates right
away, and continue to check regularly so you don't miss out on any of the good stuff! Visit www.numark.com for the latest
updates.
MIXDECK & TRAKTOR NUMARK EDITION
MIXDECK comes with Native Instruments' Traktor Numark Edition – digital DJ software that you can control easily with
MIXDECK connected to your computer. To use MIXDECK with Traktor Numark Edition, follow these steps:
1. Insert the included software CD into your computer and follow the on-screen instructions to install it. (Make sure you
have already done this with the included audio driver CD.)
2. Using a USB cable, connect your computer to MIXDECK's USB SLAVE connector.
3. Press MIXDECK's SOURCE button and turn the PARAMETER knob to select "USB-MIDI," putting it in USB MIDI Mode.
4. Open Traktor Numark Edition. A window will appear prompting you to select "Demo," "Purchase" or "Activate." Click
"Activate."
5. Enter the serial number you received with the CD.
6. After activating the software, the Start Setup Wizard will appear. Choose "Numark" as your "setup" and "Mixdeck LE" as
your "device."
7. Click "Apply." MIXDECK is now mapped to control Traktor Numark Edition.
ROUTING AUDIO OUTPUTS IN TRAKTOR NUMARK EDITION
If you are using the MIXDECK with Native Instruments' Traktor Numark Edition software applications, please see the example
and instructions below for information on routing your audio outputs to take full advantage of cueing and monitoring.
1. In Traktor, click on Preferences.
2. Choose Audio Setup and click on the Soundcard tab.
3. Next, under the Audio Device pull-down menu, select MIXDECK.
4. Then click on the Output Routing tab.
5. Lastly, you can choose which outputs you would like to use for your Master and Monitor channels from the pull-down
menu on the bottom. Since the Headphone output on the MIXDECK is tied to the Output 2 stereo RCA pair, we
recommend using the Output 1 pair as your Master channel and the Output 2 pair as your Monitor channel.
Additional Information: You may also wish to send each virtual "deck" independently to each output pair on the
MIXDECK for use with an external mixer. To do so, please select External as the Mixer Mode in the Output Routing
tab. You will then be able to decide which deck is being sent to which output pair.
Check with your software
12
Note: Before connecting MIXDECK to your
computer, insert the included CD into your
computer to install the necessary drivers.