grandimpianti WFM 8 Instructions Pour L'installation Et Mode D'emploi page 19

TO" field using the "UP" and "DOWN"
keys. Press "ENTER" to confirm.
Select the program you wish to copy from or
to using the "UP" and "DOWN" keys. Press
"ENTER" to confirm.
The programmer will next prompt
"COPY?". Press "ENTER" to copy between
cycles or programs or press "MODE" to
cancel.
Whether you chose to confirm or cancel the
copy, press "MODE" to exit.
DESCRIPTION OF
PROGRAMMABLE FUNCTIONS
Machine parameters are those required to
effect marginal changes to the wash
programs without having to access cycle or
step programming.
These functions enable the user to override
existing actions or add new ones in a wash
cycle. This does not alter the program
features in a radical manner, though.
The "MACHINE PARAMETERS" menu is
accessed as follows:
Open the washer door: all programming
actions must be performed with the door
open. The programming environment
cannot be accessed when the door is closed.
Hold down the " MODE" key until the
"MACHINE PAR." reading appears. Press
"ENTER" to confirm. The display will then
read the following items:
COOL
SPIN
PREWASH
DELAYED START
BUZZER
HEATING
ENABLE
RESET
The various items are described below.
These functions affect only the currently
selected wash cycle and remain effective
until they are disabled.
COOLING
Cool: This function decides whether the
wash bath is to be cooled right before it is
drained off. As a rule, cooling is aimed to
prevent the garments from undergoing a
thermal shock as they go, for example, from
a 90°C wash step to ambient temperature
rinsing.
Select "COOL" using the "UP" and
"DOWN" keys.
Confirm the selection by "ENTER".
Programs/cycles and their respective cooling
setting can be scrolled using the "UP" and
"DOWN" keys. Move to the desired cycle and
press "ENTER". Then choose between "YES"
and "NO" using the "UP" and "DOWN" keys
and press "ENTER" to confirm.
Press "MODE" to exit.
SHORT SPINNING
Spin: This function allows to acknowledge
the standard-selected spinning, reduce it to
one-minute spinning or eliminate it
altogether. Select "SPIN" using the "UP"
and "DOWN" keys.
Confirm the selection by "ENTER".
Programs/cycles and their respective cooling
setting can be scrolled using the "UP" and
"DOWN" keys. Move to the desired cycle
and press "ENTER". Then again using the
"UP" and "DOWN" keys choose among:
NORMAL
REDUCED
NO SPINNING
Press "ENTER" to confirm.
Normal: the machine carries out standard
final spinning. Reduced: one-minute final
spinning. Spinning length is applied to the
last spinning speed. The acceleration ramp
is never reduced.
No spinning: final spinning is not carried
out.
Press "MODE" to exit.
NO PREWASHING
Prewash: Generally speaking, all programs
include prewash. The purpose of this
function is actually to override prewash.
This is especially useful when handling
laundry that is not heavily soiled.
Select "PREWASH" using the "UP" and
"DOWN" keys.
Confirm the selection by "ENTER".
Programs/cycles and their respective
prewash setting can be scrolled using the
"UP" and "DOWN" keys.
desired cycle and press "ENTER". Then
choose between "YES" and "NO" using the
"UP" and "DOWN" keys and press
"ENTER" to confirm.
Press "MODE" to exit.
DEFERRED CYCLE START
Delayed START: This function defers
machine start up to a maximum of 24 hours.
As soon as the scheduled time has elapsed
the machine starts automatically.
This function defers machine start up to a
maximum of 24 hours. As soon as the
scheduled time has elapsed the machine
starts automatically.
When waiting for the deferred start the
machine reads the countdown. If during the
countdown the "START" key is pressed, the
machine immediately starts the cycle that
was originally selected. Select "DELAYED
START" using the "UP" and "DOWN"
keys.
Confirm the selection by pushing "ENTER".
The parameter status, i.e. either
"DISABLED" or "ENABLED" will appear.
Press "ENTER" to change the selection.
Use the "UP" and "DOWN" keys to make
your selection in minutes and/or hours and
then press "ENTER" to confirm.
Press "MODE" to exit.
As soon as the "START" key is pushed the
countdown starts and the display reads the
following message:
Start scheduled in:
countdown (time remaining to the beginning
of the cycle)
ENABLE/DISABLE BUZZER
Buzzer: Each time a key is pressed the
buzzer gives out a short loud beep. This can
be eliminated by accessing this function.
20
Select "BUZZER" using the "UP" and
"DOWN" keys.
Confirm the selection by "ENTER".
The parameter status, i.e. either
"DISABLED" or "ENABLED" will appear.
Press "ENTER" to change the selection.
Use the "UP" and "DOWN" keys to select
your value and then press "ENTER" to
confirm.
Press "MODE" to exit.
CHANGING HEATING
TEMPERATURE
Heating: The maximum wash bath
temperature reached through heating in any
cycle can be lowered by 10°C. Select
"HEATING" using the "UP" and "DOWN"
keys.
Confirm the selection by "ENTER".
The parameter status, i.e. either "NORMAL"
or "REDUCED" will appear. Press
"ENTER" to change the selection. Use the
"UP" and "DOWN" keys to make your
selection and then press "ENTER" to
confirm.
Press "MODE" to exit.
ENABLING CYCLES
Enable: When one or more cycles are not
Move to the
desired, it is possible to hide them from the
available alternatives. This means that they
are not erased but only concealed from the
user interface menu. The enabled cycles can
be scrolled using the "SELECT" and "UP"
or "DOWN" keys and the disabled cycles
will not be listed. Select "ENABLE" using
the "UP" and "DOWN" keys.
Confirm the selection by pushing "ENTER".
Using the "UP" and "DOWN" keys it will be
possible to scroll all programs and their
enable/disable settings. Move to the desired
cycle and press "ENTER". Again using the
"UP" and "DOWN" keys, choose between
"ENABLED" and "DISABLED" and press
"ENTER" to confirm.
Press "MODE" to exit.
RESET:
Temperature: As a rule, once the machine
has reached the temperature set for a cycle
in which heating is expected, it holds the
temperature for the time that the program
establishes. Using this parameter it is
possible to disable this function.
Level: As a rule, once the machine has
reached the water level set for a cycle in
which water talke-in is expected, it holds
the water level for the time that the program
establishes. Using this parameter it is
possible to disable this function.
7.4 USEFUL ADVICE FOR THE USE
OF THE MACHINE
Remember that loading 80% of the rated
capacity provides better wash results.
Mind that more soap does not mean better
wash: on the contrary, using too much
washing agent only leads to unnecessary
pollution. The right amount of soap is
indicated by the manufacturer according to
the relevant water hardness.