grandimpianti WFM 8 Instructions Pour L'installation Et Mode D'emploi page 15

5) THE BRACKETS THAT FASTEN THE
TUB MUST ABSOLUTELY
REMOVED BEFORE
STARTUP.
6) Be sure that the instruction booklet is not
left in the package and lost.
The packaging materials (plastic bags,
expanded polystyrene, wood, cardboard,
nails, etc.) represent a safety hazard and
consequently must not be left within the
reach of children. Collect and keep for
further transportation or long-term storage
(cfr. chapter 9). Before connecting the
appliance, check that the rating plate data
correspond to those of the existing electrical
system. The appliance must only ever be
used for the purposes it was explicitly
designed for.
5. GETTING THE APPLIANCE
STARTED
5.1 POSITIONING REQUIREMENTS
These washing machines demand no
positioning requirement but a flat, level and
sturdy surface.
Align by the use of a spirit level.
For servicing purposes, it is advisable to
leave at least 500mm (1000 for model 22)
between the rear face of the machine and the
wall behind.
Besides, when machines are installed in a
line, leaving at least 30mm between one
machine and the next is recommended.
Provide for a floor drain at an elevation
below the machine drain, that can be
connected to the washing machine, using
the supplied elbow fitting.
CAUTION! Repeat levelling after moving
the machine.
5.2 SPACE REQUIRED FOR
INSTALLATION, USE AND
MAINTENANCE
The washing machine requires the minimum
space indicated in the dimensional figures
(cfr. figure 1).
1) Power supply line with automatic
differential switch and thermomagnetic
cutout upstream *.
2) Interlocked socket including fuses and
manual multipolar switch.
3) Power supply plug.
4) Shutoff taps for water inlets.
5) Grille or plate (preferred) for closing
drain pit.
6) Rubber hose for water drain, diam. 3"
(provided).
7) Drain pit, flow rate of 160 litres/min.
8) Circular door.
9) Hard water inlet of 3/4".
10) Warm water inlet of 3/4".
11) Soft water inlet of 3/4".
12) Steam inlet of 3/4" (only on steam-
heated models).
13) Cable clamp for power supply inlet
(models 8-11-18).
14) Template to be used for positioning
machine-anchoring bolts.
15) 3 tubes for hard, warm and soft water
intake (provided)
16) Flexible tube of 3/4" for steam connection
BE (supplied with steam-heated models only).
MACHINE 17) Mechanical filter of 3/4" (attached to
steam-heated models).
18) Steam supply line, pressure comprised
between 4 and 6 bar, consumption
approximately 15 kg/h (steam models only).
19) Steam shutoff tap (steam-heated models
only).
20) Condensed water drain of 3/4" (only
with indirect steam models 8-11-18).
21) Cable clamp for power supply inlet
(model 22)
22) Inverter casing (model 22 only)
23) Connection for liquid-soap tubes (model
for 22kg only)
22) Connection for cycle-programming cable
(using the appropriate connection kit, a PC
and the relevant software)
25) Water drain
* The cutoff switch must be in a position
allowing easy access to the operator in any
EMERGENCY event (maximum distance 3
m).
5.3 ALLOWABLE AMBIENT
CONDITIONS FOR PROPER SERVICE
(INFORMATION FOR THE USER)
Let these conditions be known to machine
users.
- TYPE OF ROOM: CLOSED
- MINIMUM TEMPERATURE:
(note: when ambient temperature is
below 10°C, electronic parts may work
irregularly)
- MAXIMUM TEMPERATURE: 40°C
- RELATIVE HUMIDITY: 75% H.R.
- LIGHTING: 100 LUX (value valid for
Italy; given the variety of regulations
regarding lighting in working premises,
for other national provisions it will be
necessary to consult the relevant national
codes).
5.4 ELECTRICAL CONNECTION
The machine must be installed by
professionally qualified personnel, in
accordance with the instructions provided
by the manufacturer and local regulations.
Incorrect installation may cause harm to
persons, animals or property. The
manufacturer assumes no responsibility for
such damage.
Make sure power supply voltage corresponds
to that indicated on the rating plate of the
washing machine. Consider also that the
maximum allowable power voltage variation
is ±10%.
IMPORTANT:
CONNECTING THE MACHINE TO
EARTH IS MANDATORY.
To this purpose, the terminal block is fitted
with a specific contact, which must be
connected according to the regulations in
force. The manufacturer assumes no
responsibility for damage resulting from
nonobservance of this accident prevention
principle.
In compliance with the latest accident
prevention provisions, the machine is
10°C
16
provided with an external terminal for
equipotential connection.
Upstream of the appliance an automatic
omnipolar cutoff switch must be provided
for, with contact gaps no smaller than 3 mm,
and set according to the maximum rated
input (cfr. table 2 below and machine rating
table).
N um b er
Tota l m a chine po we r
o f p oles
E lec tric S te am
23 0/3 40 0/3
hea ting hea ting
from 5 50 to
3 4
110 0W
from 15 00
3 4
to 25 00 W
from 60 00
3 4
to 1 00 00W
from 1 00 00
3 4
to 1 30 00W
from 1 80 00
3 4
to 2 50 00W
Provide for a cable carrier duct of outer
diameter 20 mm (30 mm for model 22)
between the cutoff switch and the appliance's
power supply inlet. Use the cable clamp
existing on the machine's back to introduce
the power cord and, after the cables have
been connected to the terminal board
according to the sequence appearing on the
same, stop the cable by the plastic nut. Use
one of the cable types appearing in the table.
Make sure it is fire-proof and properly
protected.
Number of
Total machine power
leads
Electric Steam/w arm
230/3 400/3 230/3
heating w ater heating
f rom 550 to
3 4
H05VV-F H05V V-F
1100W
f rom 1500
3 4
H05VV-F H05V V-F
to 25000 W
f rom 6000 to
3 4
A 07VV-F A 07V V-F
10000W
f rom 10000 to
3 4
A 07VV-F A 07V V-F
13000W
f rom 18000 to
3 4
S07VV-F A 07V V-F
25000W
CAUTION!
These appliances are equipped with
electronic control devices, e.g. control card
and inverter. To be CE type-approved, such
devices must include noise filters complying
with EMC standards on eddy current
emission. To operate properly, these filters
leak a small current of approximately 10-
15mA through the earth lead.
Therefore every machine must be fitted with
its own system-protecting differential cutoff
switch. Avoid connecting more then one
appliance, whatever their capacity or brand,
downstream of a single differential cutoff
switch.
IMPORTANT: TILT SWITCH
ADJUSTMENT
All extracting washers are equipped with a
device that aborts spinning steps when severe
imbalance poses a threat to the mechanical
parts composing the machine.
To access this safety device, open the top lid
cover: it is approximately located at the
machine's topmost point. Adjust this switch
only after the wall cutoff switch has been
turned off and the machine is disconnected
from the power mains.
Adjustment of this switch is reserved to the
authorised and qualified personnel.
This device consists of a microswitch secured
to the machine's frame, and it is driven by a
Trip res .
R ated input In
curr.Id
23 0/3 4 00 /3
6 6 30m A
1 6 16 30m A
20 -30 16 30m A
30 -40 25 30m A
50 -70 3 0-40 30m A
Lead c ros s
Cable type
sec tion sq.mm
400/3 230/3 400/3
1 1
2,5 1
6 2,5
6 4
10 6