Oscartielle ANDROMEDA 210 Mode D'emploi page 20

The plug-in units are supplied already fitted with a 2,5 m cable and plug (see FIG. 8), so the unit must not be installed
more than 2,5 m from the nearest wall socket. The cabinet should be connected to its own fixed current socket (i.e.
without extension leads or multiple plugs).
The cable should be fully extended, protected from accidental hits and located where it can not be caught or trod upon. It
must be away from water and other liquids and heat sources and must not be damaged. In case of breakage of the power
cable of the cabinet, it must be replaced by the manufacturer or by institution in charge of it. The plug must still be
accessible even after installing the unit.
Warning: Follow the Manufacturer's instructions to install the unit, using qualified personnel and in compliance with the
electrical regulations for the specific country (electrical safety standards and laws, accident and fire prevention laws, EC
directives). Incorrect installation may cause injury and damage. The Manufacturer cannot be held liable for this.
The unit must be earthed. The Manufacturer cannot be held liable for any damage or injury should this safety regulation
be ignored. If the unit is to be installed far from the electrical sockets, suitable electrical connections are needed and
these must comply with the prevailing standards. The use of adapter plugs is strictly prohibited. The Manufacturer
cannot be held liable for any damage or injury arising from incorrect installation.
7 - Technical details
The display unit is accompanied by a plastic envelope containing this instruction manual. This manual must be kept with
the machine. It contains all the technical data, wiring diagrams and tables needed for the unit.
The following technical data are also shown on the serial plate (FIG. 9):
1. Name and address of the manufacturer
2. Commercial name of the cabinet
3. Cabinet code
4. Cabinet serial number
5. Rating
6. Frequency
7. Max absorbed current
8. Max absorbed power
9. Max absorbed power during defrosting
10. Standard lighting power
11. Net display area
12. Type of cooling gas used
13. Weight of cooling gas loaded in each unit
14. Climatic class and reference temperature (dry bulb)
15. Electrical safety factor
16. Work schedule number
17. Work order number
18. Year of manufacture
19. Heating capacity
20. QR code
21. EAC marking
Warning: The serial plate and the warning labels must never be removed from the unit. The Manufacturer cannot be held
liable for any damage or injury if this warning is ignored.
The Manufacturer states that this unit complies with Italian legislative degree n° 108 dated 25.01.1992, implementing
EEC Directive 89/109 concerning materials and objects that come into contact with food.
8 - Loading and use of the unit (start-up)
If the display unit has been tipped during positioning and installation, wait at least three hours before starting it up in order
to give the lubricating oil enough time to collect in the compressor! The refrigerating unit may be irretrievably damaged if
this precaution is ignored.
The display unit can only be started up for the very first time after complying with points 3 and 4 above.
With the unit unplugged, remove the plastic film protecting the insides and outside and then clean (follow the instructions
in point 11 below).
Fit the various shelf supports at the height required, as shown in FIG. 12. FIG. 1 shows the best distances between
shelves.
Plug in the unit (having followed the instructions in point 6) and flip the switch fitted upstream (if any). A slight humming of
the motor and the lighting-up of the display indicate that the unit is powered up.
Switch on the lights using the switch on the decorative front panel (see FIG. 11).
The cabinet is equipped with a display located on the front decorative canopy FIG. 11
The electronic control instruction handbook for the displays is attached to the instruction manual. A password guarantees
that these devices cannot be tampered with.
The product can be loaded some hours after the unit has started its cooling cycle (check the temperature shown on the
display).
The unit is designed to display food products and so maintains the temperature of the product; it does not lower it. The
product should, therefore, only be loaded once the right storage temperature has been reached.
18