Assembly Instructions - Health O Meter PROPLUS 4021 Mode D'emploi

ASSEMBLY INSTRUCTIONS

Before Assembly:
The ProPlus® 4021Digital Handrail Scale is shipped disassembled in one carton. Carefully inspect the carton for shipping
damage before unpacking. If damage is found, contact your shipper or Health o meter® Professional representative
immediately. Claims must be filed with the shipper as soon as possible after receipt of the package, if there are damages.
The following information details what you will find inside the main carton, as you unpack the parts for assembly.
Remove each assembly from the carton and unwrap packing material carefully, to prevent scratching the unit's parts. Set the
carton aside, for storage. To avoid damaging the scale parts when unpacking it, do not use a box cutter, knife, scissors or
any sharp object to open the protective inner packaging.
Parts List:
(1) Base (Platform) Assembly
(1) Center Handrail
(2) Side Handrails
(1) Handle
(1) User information
(1) Box Containing:
(1) Display Assembly
(1) Small, Long Box
Tools required: Phillips head screwdrivers (not included), Allen wrenches (included).
IMPORTANT: Please refer to the maintenance parts list on page 11 for more details about each part.
A detailed view of the scale is illustrated on page 10.
Assembling a 4021 Scale:
It is recommended that the assembly be done by two people.
1. Place scale base on a flat, level, dry floor.
2. Locate and pick up the center handrail, then find the load cell cable, untie it and pull it out the bottom.
3. Position the handrail over the platform and feed the cable through the handrail support in the base, being sure
not to pinch the cable.
4. Slide the center handrail over the handrail supports on the base and fasten the handrail to the handrail supports
using four (4) M8 1.25 x ¾ screws (B), four (4) M8 washers (F) and the medium Allen wrench (see Figure 1).
Lightly tighten the screws. DO NOT OVERTIGHTEN. Wait to tighten until Step 6.
5. Attach the left / right side handrails to the center handrail and platform using the two (2) M10 1.5 x 1½ screws
(A), eight (8) M8 1.25 x ¾ screws (B) with eight (8) M8 washers (F), and lightly tighten.
6. Starting at the top and working down the sides and base, fully tighten all 14 screws in the handrails.
7. Attach the handle to the back of the center handrail using two (2) medium M6 1.0 x ½ screws (C), and tighten.
8. Pull forward on the side handrails to tip the scale and gently place it face down on the floor.
9. Grasp the load cell cable protruding from the bottom of the base and feed it through the protective metal shield
above the wheel in the base of the scale, then plug it into the load cell port in the center of the base.
10. Pull the excess cable through the top of the scale.
11. Thread the 4 feet into the underside of the base. Each foot should be completely hand tightened and then
backed out 1-½ full turns. This allows for proper load cell operation for accuracy of the scale.
12. Carefully tilt the scale back to an upright position on the floor. DO NOT DROP THE SCALE. Adjust the feet, to
level the scale. Be certain that the feet are NOT completely tightened into the base (see Step 11, above).
The Small, Long Box Contains:
(1) Box Containing the Power Adapter
(4) Feet
(1) Rear Cover for Display
(1) Adapter Holder
(3) Allen Wrenches—small, medium, large
(1) Plastic Bag Containing:
(1) Front Cover for Display Support
(1) Small Rear Cover for Display Support
Hardware for Assembly (Figure 1)
Figure 1