Publicité
Safety, performance, and dependability have been given
top priority in the design of your electric lawn trimmer/ edge
trimmer.
INTENDED USE
The electric lawn trimmer/ edge trimmer is only intended for
use outdoors by a standing operator.
The product is designed for cutting grass, light weeds,
and other similar vegetation at or about ground level.
The cutting plane should be approximately parallel to the
ground surface.
The product should not be used to cut or trim hedges,
bushes, or other vegetation where the cutting plane is not
at or about ground surface level.
Do not use the product for any other purpose.
GENERAL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, fi re and/or serious injury.
WARNING
When using the product, the safety rules must be
followed. For your own safety and that of bystanders,
please read these instructions before operating the
product. Please keep the instructions safe for later use.
WARNING
The product is not intended to be used by
children or persons with reduced physical,
mental or sensory capabilities. Children
should be adequately supervised to ensure
they do not play with the
WARNING
Some regions have regulations that restrict the use of
the product. Check with your local authority for advice.
TRAINING
■
Never allow children or people unfamiliar with these
instructions to use the product. Local regulations may
restrict the age of the operator.
■
Read the instructions carefully. Be familiar with all
controls and the proper use of the product.
■
Keep bystanders, children and pets 15 m away from
the area of operation. Stop the product if anyone enters
the area.
■
Never use the product when you are tired, ill or under
the influence of alcohol, drugs or medicine.
■
Keep in mind that the operator or user is responsible
for accidents or hazards occurring to other people or
their property.
product.
ELECTRICAL SAFETY
■
Power plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
■
Prevent unintentional starting. Always check that the
switch is in off position before plugging in the product
to the power supply. Do not carry a plugged in product
with your finger on the switch.
■
Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body
is earthed or grounded.
■
Do not operate the product when there is a risk of
lightning.
■
Do not expose the product to rain or wet conditions.
Water entering an appliance will increase the risk of
electric shock.
■
Electrical power should be supplied via a residual
current device (RCD) with a tripping current of not more
than 30 mA.
■
Before every use, examine the power cord for damage.
If there are signs of damage, it must be replaced.
Always uncoil the power cord during use; coiled cables
can overheat.
■
If you need to use an extension cable, ensure it is
suitable for outdoor use and has a current capacity
sufficient to supply your product. The extension cord
cable should be marked with either "H05 RNF" or H05
VV-F". Check it before every use for damage. Always
uncoil it during use because coiled cables can overheat.
Damaged extension cables should not be repaired;
they should be replaced with an equivalent type.
■
Do not use the product if the electric cables are
damaged or worn.
■
If the power cord or extension cable becomes
damaged during use, disconnect from the power supply
immediately. Do not touch the electric cables until the
power supply has been disconnected.
■
Make sure the power cord is positioned so that it
cannot be damaged by the cutting means and will not
be stepped on, tripped over, or otherwise subjected to
damage or stress.
■
Never pull the power cord to disconnect from the power
supply.
■
Never pick up or carry the product by the electric cable.
■
Keep the power cord away from heat, oil, and sharp
edges.
■
Make sure voltage is correct for your product. A
nameplate on the product indicates the product's
voltage. Never connect the product to an AC voltage
that differs from this voltage.
■
Make sure the switch is in off position before
disconnecting from power supply.
PREPARATION
■
Wear full eye and hearing protection while operating the
product. If working in an area where there is a risk of
falling objects, head protection must be worn.
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
English |
1
Publicité
