Intended Use; Safety Information - Scheppach HS110 Traduction Des Instructions D'origine

• Centre struts (4x)
• Rubber feet (4x)
• Stand bracket (2x)
• Table supports (4x)
• Translation of Original Operating Manual
a. Hexagon head screw with collar, 8 units;
b. Carriage bolt, 12 units;
c. U-washer, 18 units;
d. Spring washer, 12 units;
e. Nuts, 18 units
f. Hexagon head screw with cross slot with mounted
U-washer/spring washer, 12 units;
g. Open-end spanner, size 8/10
h. Ring spanner, size 10/22
i. Allen key HX 6

4. Intended use

The table circular saw is used for cutting all types of
wood lengthwise and crosswise (only with the trans-
verse stop), depending on the machine size. All types
of round timbers must not be cut with it. The machine
may be used only for its prescribed purpose.
Any other use beyond that is considered to be not in
accordance with the designated purpose. The user/
operator is liable for all types of resulting damage or
injury and not the manufacturer.
The only saw blades which may be used are those which
are suitable for the machine (HM or CV saw blades).
The use of any type of HSS saw blades and cutting
discs is prohibited. Use in accordance with the desig-
nated purpose is also deemed to include observance
of the safety instructions, as well as the assembly and
operating instructions in the operating manual.
Individuals who operate and maintain the machine
must be familiar with it and must have been instruct-
ed in possible hazards. Moreover, the latest accident
prevention regulations must be strictly observed.
Other general rules in the ields of occupational health
and safety technology must be complied with.
m Caution!
When using equipment, certain safety precautions
must be complied with in order to avoid injuries and
damage. You should therefore read these operating
instructions / safety instructions carefully. Keep these
in a safe place so that the information is available to
you at all times. Should you give the device to anyone
else, please give them these operating instructions
/ safety instructions as well. We assume no liability
for accidents or damage caused by failure to observe
these instructions or the safety instructions.
Changes to the machine will cause the manufacturer'
s liability with respect to any resulting damage to be
completely excluded.
28 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Even when the device is used in accordance with the
designated purpose, it is nevertheless not possible
to completely eliminate certain residual risk factors.
Due to the design and structure of the machine, the
following risks may occur:
• Touching the saw blade in the area of the saw
which is not covered;
• Reaching into the running saw blade (cuts)
• Kickback of workpieces and workpiece parts.
• Saw blade breaks.
• Ejection of faulty hard metal parts of the saw blade.
• Hearing damage if the necessary hearing protec-
tion is not used.
• Emissions of wood dust which are harmful to the
health when used in closed rooms.
m Please note that the use of our devices in accord-
ance with the designated purpose does not include
commercial, handicraft or industrial applications. We
assume no warranty if the device is used in commer-
cial, handicraft or industrial businesses or for equiv-
alent purposes.

5. Safety information

m Caution! The following basic safety precau-
tions must be observed while using electric tools
to protect against electric shock, injury and risk
of ire. Please read all instructions before using
this electric tool and keep the safety instructions
in a safe place.
Safe operation
1. Keep work area clear
- Cluttered areas and benches invite injuries.
2. Consider work area enviroment
- Do not expose tools to rain.
- Do not use tools in damp or wet locations.
- Keep work area well lit.
- Do not use tools in the presendce of lammable
liquids or gases.
3. Guard against electric shock
- Avoid body contact with earthed or grounded
surfaces (e.g. pipes, radiators, ranges, refriger-
ators).
4. Keep away from children!
- Do not let other people touch the tool or the
cable, keep them away from your work area.
5. Store idle tools
- When not in use, tools should be stored in a dry
locked- up place, out of the reach of children.
6. Do not force the tool
- It will do the job better and safer at the rate for
which it was intended.
7. Use the right tool
- Do not force small tools to do the job of a heavy
tool.