Before Starting The Equipment - EINHELL PICOBELLA Traduction Du Mode D'emploi D'origine

layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be
considered (for example, times in which the
electric tools are switched off and times in which
the tool is switched on but operates without load).

5. Before starting the equipment

The equipment is supplied without batteries
and without a charger.
5.1 Turn the steady grip out of the transport
position (Fig. 3-4)
Important! For transport reasons the steady
grip is turned 90° to the side. For you to be able
to work with the equipment, the steady grip must
be aligned in line with the brush housing (working
position).
1. Slacken the lock nut (8) by turning it counter-
clockwise and turn the steady grip as far as it
will go.
2. Secure the lock nut (8) by turning it clockwise.
5.2 Fitting the additional handle (Fig. 5)
Using the handle screws (6), fasten the additional
handle (16) (the screws are accessible from
below) and the holder (17) at the area provided.
5.3 Adjusting the length of the long handle
(Fig. 6)
To ensure that you have a comfortable working
position, the length of the long handle can be
adjusted.
1. Slacken the lock nut (8) by turning it counter-
clockwise.
2. To change the length of the long handle, pull
the long handle (9) out of the steady grip (18)
or push it into the steady grip.
3. Make sure that the steady grip is in the
working position (section 5.1) and secure the
lock nut (8) by turning it clockwise.
Anl_Picobella_SPK7_USA.indb 12 Anl_Picobella_SPK7_USA.indb 12
EN
5.4 Adjusting the additional handle (Fig. 5)
Undo the two fastening screws (6) on the
additional handle until it can be moved in any
direction without any great resistance. Set the
required position and tighten the two fastening
screws (6) again.
5.5 Fitting the cleaning brushes (Fig. 7-10)
Remove the brush covers on the sides (Fig. 7 /
Item 19). The product is supplied complete with
a 2-piece MEDIUM nylon brush (black). A nylon
brush (Fig. 2 / Item 15) is equipped with a side
brush. The cleaning brushes have rubber caps
(Fig. 8 / Item 20) on the outside. Slot the nylon
brush with side brush onto the brush mount (Fig.
9) on either the left or right side according to your
requirements and the other nylon brush onto the
other brush mount. Fit the brush covers back in
place. The wide brush cover (Fig. 7 / Item 19) is
for the nylon brush with side brush. The MEDIUM
nylon brush is ready-fi tted (Fig. 10).
The SOFT nylon brush (yellow/green) (Fig. 11)
and the ULTRA metal brush (Fig. 12) must be
fi tted in the same way, but do not have a side
brush. They come supplied complete with a
narrow brush cover which must be used instead
of the wide brush cover.
Warning! There is a risk of injury from the bristles
of the metal brush – wear safety gloves.
5.6 Removing cleaning brushes
Remove the brush covers on the sides (Fig. 7
/ Item 19). Press the middle of the rubber cap
(Fig. 8 / Item 20) to actuate the release button
underneath and pull off the brush at the same
time.
Warning! There is a risk of injury from the bristles
of the metal brush – wear safety gloves.
5.7 Water inlet connector (Fig. 14 – 17)
To achieve top cleaning results quickly, we
recommend wet cleaning.
Important!
•
Observe the requirements of EN 1717
in relation to the connection of the water
connection to the drinking water network.
Consult a specialist plumbing company.
•
Never direct the water jet at electric cables or
the equipment itself.
•
The water temperature must be between
+41°F (+ 5°C) and +95°F (+ 35°C).
•
Do not use water that is dirty, gritty or
contains any chemical products, as these
- 12 -
01.07.2020 11:37:55 01.07.2020 11:37:55