Intended Use; Technical Data; Before Starting The Equipment - EINHELL VARRITO Traduction Du Mode D'emploi D'origine

3. Intended use

The equipment is suitable for sanding/grinding
small areas. For sanding/grinding larger areas
the vacuum extractor, which is available as an
accessory (see 7.3), must be used.
The equipment is designed for the sanding/
grinding of wood, iron, plastic and similar
materials using the appropriate abrasive paper.
Furthermore, the equipment is intended for
sawing wood, plastic and similar materials,
as well as scraping off glued carpets, fi lling
compound residues, old paint and similar
applications.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.

4. Technical data

Motor power supply: ............................18 V
No-load speed .............. 11000-20000 min
Sanding/grinding
area: .............3.5 x 3.5 x 3.5 in. (90 x 90 x 90 mm)
Oscillation angle: ...........................................3.2°
Weight: ......................................... 2.2 lbs (1.0 kg)
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect
condition.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
•
Wear gloves.
Anl_Varrito_SPK7_USA.indb 12 Anl_Varrito_SPK7_USA.indb 12
EN
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's construction and
layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
Be sure to read the following information before
you put the cordless equipment into operation:
•
Charge the battery pack with the charger.
An empty battery pack requires a charging
period of approximately 0.5 to 1 hour.
5.1 Fitting the plug-in tools (Figures 1-5)
•
Open the quick-release lock for changing
tools (5) as shown in Fig. 2.
(rpm)
-1
•
To fit the plug-in tools safely you should hold
the multi-tool so that the On/Off switch (1)
points down and the tool chuck (2) faces up.
•
Place the plug-in tool (e.g. the scraper) on
the tool chuck (2) so that the pins of the tool
chuck fit into the recesses in the plug-in tool.
The tool chuck (2) is magnetic in order to
secure the plug-in tool during the clamping
procedure.
•
Close the quick-release lock for changing
tools (5) again. Take care that the pins of the
chuck (2) remain in the recesses in the plug-
in tool.
•
The equipment comes with a disk (14) for
safely securing plug-in tools with recesses.
Please note the correct use (camber facing
the tool) of the disk (14) for plug-in tools with
recess as shown in Fig. 4 and 5.
Check that the plug-in tool is secure.
- 12 -
02.05.2019 16:22:53 02.05.2019 16:22:53