DeWalt DWE43214 Guide D'utilisation page 9

Features
DWE43214, DWE43214n, DWE43214nVs,
DWE43244n
E-switch Protection™
The ON/OFF paddle switch has a no-volt release function.
In the event of a power outage or other unexpected shut
down, the paddle switch will need to be cycled (turned off
and then on) to restart tool.
E-Clutch™
This unit is equipped with an E-Clutch™ (Electronic Clutch),
which in the event of a stall or wheel pinch, the unit will
be shut off to reduce the reaction torque to the user. The
switch needs to be cycled (turned off and then on) to
restart tool.
Brake
When the paddle switch is released the motor immediately
turns off and electronically brakes stopping the
accessory quickly.
Kickback Brake™
When a severe pinch, stall, or bind-up event is sensed the
electronic brake engages with maximum force to quickly
stop the wheel, reduce the movement of the grinder, and
shut the grinder off. Turn the unit on to restart tool.
Constant Clutch™
When overloaded or stalled the motor torque is reduced. If
load is reduced the torque and RPM will increase. If the tool
is stalled for an extended amount of time it will shut-off and
require the switch to cycle to restart.
Variable Speed Dial (Fig. A)
DWE43214nVs Only

WARNING: Regardless of the speed setting, the rated
speed of the accessory must be at least equal to the
maximum speed marked on the power tool.
The variable speed dial offers added tool control and
enables the tool to be used at optimum conditions to suit
the accessory and material.
• Turn the dial 12 to the desired level. Turn the dial to the
right for higher speed and to the left for lower speed.
LED Indicator (Fig. A)
The LED indicator 13 will remain lit green during normal
activity, or blink in a pattern of red light to alert you a
tool protection feature has been activated. Refer to the
LED Guide at the back of this manual for explanations of
blink patterns.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Accessories
The capacity of the DWE43214, DWE43214N, DWE43214NVS
is 5" (125 mm) diameter x 1/4" (6.35 mm) thick
grinding wheels.
The capacity of the DWE43244N is 6" (150 mm) diameter x
1/4" (6.35 mm) thick grinding wheels.
It is important to choose the correct guards, backing pads
and flanges to use with grinder accessories. See page 14 for
information on choosing the correct accessories.

WARNING: Handle and store all abrasive wheels
carefully to prevent damage from thermal shock, heat,
mechanical damage, etc. Store in a dry protected area
free from high humidity, freezing temperatures or
extreme temperature changes.
Attaching Side Handle (Fig. A)

WARNING: Before using the tool, check that the
handle is tightened securely.
Screw the side handle 5 tightly into one of the holes on
either side of the gear case. The side handle should always
be used to maintain control of the tool at all times.
Guards

CAUTION: Guards must be used with all grinding
wheels, cutting wheels, sanding flap discs, wire
brushes, and wire wheels. The tool may be used
without a guard only when sanding and surface
finishing with conventional sanding and surface
finishing diamond pads. Refer to Figure A to see
guards provided with the unit. Some applications may
require purchasing the correct guard from your local
dealer or authorized service center.
nOTE: Edge grinding and cutting can be performed with
Type 27 wheels designed and specified for this purpose;
1/4" (6.35 mm) thick wheels are designed for surface
grinding while thinner Type 27 wheels need to be examined
for the manufacturer's label to see if they can be used for
surface grinding or only edge grinding/cutting. A Type 1
guard must be used for any wheel where surface grinding
is forbidden. Cutting can also be performed by using a
Type 41 wheel and a Type 1 guard.
nOTE: See the Accessories Chart to select the proper
guard / accessory combination.
Adjusting and Mounting Guard (Fig. C, D)

CAUTION: Turn unit off and unplug the tool before
making any adjustments or removing or installing
attachments or accessories.

CAUTION: BEFORE operating the tool, identify which
guard adjustment option your tool is set to.
Adjustment Options
For guard adjustment, the guard release lever
one of the alignment holes 14
a ratcheting feature. Your grinder offers two options for
this adjustment.
• One-touch TM : In this position the engaging face
is slanted and will ride over to the next alignment
hole when guard is rotated in a clockwise direction
English
7 engages
on the guard collar using
7