Scheppach HC50Si Traduction Des Instructions D'origine page 84

Check to see that the moving parts operate freely
–
and don't stick, and to make sure no parts are
damaged. All parts must be mounted properly and
meet all the conditions for ensuring trouble-free
operation of the electric tool.
Damaged safety equipment and parts must be
–
properly repaired or replaced by a professional
facility, unless otherwise indicated in the user
manual.
– Damaged switches must be replaced by a cus-
tomer service facility.
Never use an electric tool whose switch cannot
–
be turned on and off.
21. CAUTION!
Using other insertion tools and accessories may
–
cause injury.
22. Have your tool repaired by an electrical expert
This electric tool meets applicable safety re-
–
quirements. Repairs must be made only by an
electrical expert using original replacement
parts. Otherwise accidents many occur.
Additional safety instructions
• Only use cable reels in the unrolled state.
• Do not use any faulty or damaged connection ca-
bles.
• Do not use the cable for purposes for which it is
not intended! Do not use the cable to pull the plug
out of the outlet. Protect the cable from heat, oil
and sharp edges.
• Important!
For your own safety, only use accessories and
–
additional equipment that are indicated in the
operating manual or have been recommended
or indicated by the manufacturer. Use of other
tools or accessories that those recommended in
the operating manual or in the catalogue could
represent a personal danger to you.
• Noise
Wear hearing protection when using the com-
–
pressor.
• Replacing the connection line
– If the connection line is damaged, it must be
replaced by the manufacturer or an electrician to
avoid danger. Danger due to electrical shocks.
• Filling tyres
Check the tyre pressure immediately after fill-
–
ing using a suitable pressure gauge, e.g. at a
petrol station.
• Street-legal compressors in construction site op-
eration
Ensure that all hoses and fixtures are suitable
–
for the maximum permissible working pressure
of the compressor.
• Set-up location
Only set up the compressor on a flat surface.
–
• It is recommended to equip the feed hoses with a
safety cable in case of pressure above 7 bar, e.g.
using a wire cable.
84 GB
Heruntergeladen von manualslib.de Handbücher-Suchmachiene
Warning! This electric tool generates an electro-
magnetic field during operation. This field can im-
pair active or passive medical implants under certain
conditions. In order to prevent the risk of serious
or deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool.
Safety instructions for working with compressed air
and blasting guns
• The compressor pump and lines can become
very hot during operation. Touching these parts
will burn you.
• The air which is sucked in by the compressor must
be kept free of impurities that could cause fires or
explosions in the compressor pump.
• When releasing the hose coupling, hold the hose
coupling piece with your hand. This way, you can
protect yourself against injury from the rebound-
ing hose.
• Wear safety goggles when working with the blow-
out pistol. Foreign bodies or blown off parts can
easily cause injuries.
• Do not blow at people with the blow-out pistol and
do not clean clothes while being worn. Risk of in-
jury!
Safety information for paint spraying
• Do not process any paints or solvents with a flash
point below 55° C. There is a risk of explosion!
• Do not heat up paints or solvents. There is a risk
of explosion!
• If hazardous liquids are processed, wear protec-
tive filter units (face guards). Also, adhere to the
safety information provided by the manufacturers
of such liquids.
• The details and designations of the Ordinance on
Hazardous Substances, which are displayed on
the outer packaging of the processed material,
must be observed.
• Additional protective measures are to be undertak-
en if necessary, particularly the wearing of suitable
clothing and masks.
• Do not smoke during the spraying process and/or
in the work area. There is a risk of explosion! Paint
vapors are easily combustible.
• Never set up or operate the equipment in the vicini-
ty of a fire place, open lights or sparking machines.
• Do not store or eat food and drink in the work area.
Paint vapors are harmful to your health.
• The work area must exceed 30 m
ventilation must be ensured during spraying and
drying. Do not spray against the wind. Always ad-
here to the regulations of the local police author-
ity when spraying combustible or hazardous ma-
terials.
• Do not process media such as white spirit, butyl
alcohol and methylene chloride with the PVC pres-
sure hose. These media will destroy the pressure
hose.
and sufficient
3