Technical Data; Noise/Vibration Information - Bosch EasySander 12 Notice Originale

OBJ_BUCH-2941-001.book Page 12 Friday, August 12, 2016 8:26 AM
12 | English
Intended Use
The machine is intended for dry sanding and polishing of
wood, filler and coated surfaces. It is especially suitable for
profiles, corners or hard to reach locations.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Battery charge-control indicator / Overload indicator
2 On/Off switch
3 Battery pack *
4 Battery unlocking button *
5 Sanding sheet*
6 Sanding plate
7 Handle (insulated gripping surface)
8 Extraction outlet
9 Dust protection cap
10 Extraction adapter*
11 Vacuum hose*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.

Technical Data

Cordless Multi Sander
Article number
Rated voltage
No-load speed
No-load orbital stroke rate
Sanding sheet surface
Orbit diameter
Weight according to EPTA-
Procedure 01:2014
Permitted ambient temperature
– during charging
*
– during operation and during
storage
Recommended batteries
Recommended chargers
* limited performance at temperatures <0 °C

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-4.
Typically the A-weighted sound pressure level of the product
is less than 70 dB(A). Uncertainty K =3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-4:
2 2
a =5.5 m/s , K=1.5 m/s .
h
1 609 92A 32J | (12.8.16)
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Assembly
 Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
EasySander 12
Battery Charging (see figure A)
3 603 J76 9..
 Use only the battery chargers listed on the accessories
V= 10.8–12
page. Only these battery chargers are matched to the lith-
-1
min 11000
ium-ion battery of your power tool.
-1
min 22000
Note: The battery supplied is partially charged. To ensure full
2
cm 104
capacity of the battery, completely charge the battery in the
mm 1.2
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
kg 0,70
ducing its service life. Interrupting the charging procedure
does not damage the battery.
°C 0 ... +45
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
°C –20 ... +50
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
PBA 10,8V...
 Do not continue to press the On/Off switch after the
PBA 12V...
machine has been automatically switched off. The bat-
AL 11.. CV
tery can be damaged.
Note: If the machine should automatically switch off because
of a discharged or overheated battery, make sure to set the
machine's On/Off switch 2 to off. Charge the battery and al-
low it to cool down before restarting the machine. Otherwise
the battery can become damaged.
To remove the battery 3, press the unlocking buttons 4 and
pull the battery out of the machine to the rear. Do not exert
any force.
Observe the notes for disposal.
Bosch Power Tools