Technical Data; Before Starting The Equipment; Operation - EINHELL CE-CP 18/180 Li E Traduction Du Mode D'emploi D'origine

protection is not used (hearing loss)
•
Inhalation of abrasive particles from the
material and wheel
•
Electric shock upon contact with non-
insulated electrical parts.
If the instructions listed in the operating
instructions are not adhered to, improper handling
of the equipment may result in other residual risks
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.

4. Technical data

Motor power supply: ........................... 18 V
No load speed: .................... 500-3000 rpm (min
Polishing disk: ............................ 7 in. (Ø 180 mm)
Mounting spindle thread: .................... ⅝ -11 UNC
Weight: ........................................ 3.1 lbs (1.42 kg)
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect
condition.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
•
Wear gloves.
•
Fit the handles and any optional vibration
grips securely to the equipment's body.
If your hands get an unpleasant feeling or their
skin becomes discolored while you are using
the equipment, stop work immediately. Take long
enough rests. Failure to observe enough rests
can result in a hand and arm syndrome.
The level of strain should be estimated in the
light of the work and use of the equipment, and
suffi cient rest periods must be taken accordingly.
This can greatly reduce the level of strain
throughout the work period. Minimize the risk
of being exposed to vibrations. Look after the
equipment in accordance with the instructions in
Anl_CE_CP_18_180_Li_E_SPK7_USA.indb 14 Anl_CE_CP_18_180_Li_E_SPK7_USA.indb 14
EN
the operating manual.
If you intend to use the equipment frequently, get
in touch with your dealer and buy anti-vibration
accessories (grips).
Avoid using the equipment at temperatures of
t=50°F (10°C) or lower. Draw up a work schedule
to limit the strain caused by vibrations.
A certain level of noise nuisance is inevitable with
this equipment. Carry out noise-intensive jobs
at times that are acceptable and allowed. Where
applicable, observe rest periods and restrict
your working time to a minimum. Suitable ear
protection must be worn for your own safety and
for the safety of others nearby.

5. Before starting the equipment

Press the spindle lock only when the equipment
is at a standstill.
)
-1
5.1 Assembling the equipment (Fig. 4-6)
Important! Remove the rechargeable battery
before starting the assembly work.
The equipment is supplied without batteries
and without a charger.
5.2. Fitting the battery
Press the side pushlock button (5) of the battery
pack as shown in Fig. 8 and push the battery
pack into the mount provided. When the battery
is positioned as in Fig. 8, make sure that the
pushlock button latches in place! To remove the
battery pack, proceed in reverse order.

6. Operation

Warning!
Always remove the battery pack before making
adjustments to the equipment.
6.1 Charging the Li battery pack
The corresponding instructions can be found
in the original operating instructions for your
charger.
6.2 Battery capacity indicator (Fig. 3/pos. 8)
Press the battery capacity indicator switch (9).
The battery capacity indicator (8) shows the
charge status of the battery using 3 LEDs.
- 14 -
11.11.2019 07:52:19 11.11.2019 07:52:19