Layout And Items Supplied - EINHELL CE-CP 18/180 Li E Traduction Du Mode D'emploi D'origine

o) Do not operate the power tool near
fl ammable materials. Sparks could ignite
these materials.
Further safety instructions for all operations
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush or
any other accessory. Pinching or snagging
causes rapid stalling of the rotating accessory
which in turn causes the uncontrolled power tool
to be forced in the direction opposite of the
accessory's rotation at the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the
wheel that is entering into the pinch point can dig
into the surface of the material causing the
wheel to climb out or kick out. The wheel may
either jump toward or away from the operator,
depending on direction of the wheel's movement
at the point of pinching. Abrasive wheels
may also break under these conditions.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or
conditions and can be avoided by taking proper
precautions as given below.
a) Maintain a fi rm grip on the power tool
and position your body and arm to allow
you to resist kickback forces. Always
use auxiliary handle, if provided, for
maximum control over kickback or torque
reaction during start-up. The operator can
control torque reactions or kickback forces, if
proper precautions are taken.
b) Never place your hand near the rotating
accessory. Accessory may kickback over
your hand.
c) Do not position your body in the area
where power tool will move if kickback
occurs. Kickback will propel the tool in
direction opposite to the wheel's movement at
the point of snagging.
d) Use special care when working corners,
sharp edges etc. Avoid bouncing and
snagging the accessory. Corners, sharp
edges or bouncing have a tendency to snag
the rotating accessory and cause loss of
control or kickback.
e) Do not attach a saw chain woodcarving
blade or toothed saw blade. Such blades
create frequent kickback and loss of control.
Anl_CE_CP_18_180_Li_E_SPK7_USA.indb 12 Anl_CE_CP_18_180_Li_E_SPK7_USA.indb 12
EN
Additional safety instructions for Sanding
Operations
Safety Warnings Specifi c for Sanding
Operations:
a) Do not use excessively oversized sanding
disc paper. Follow manufacturers
recommendations, when selecting
sanding paper. Larger sanding paper
extending beyond the sanding pad presents
a laceration hazard and may cause snagging,
tearing of the disc or kickback.
Additional safety instructions for polishing
operations
Safety Warnings Specifi c for Polishing
Operations:
a) Do not allow any loose portion of the
polishing bonnet or its attachment
strings to spin freely. Tuck away or trim
any loose attachment strings. Loose and
spinning attachment strings can entangle
your fi ngers or snag on the workpiece.
This equipment is not designed to be used by
people (including children) with limited physical,
sensory or mental capacities or those with no
experience and/or knowledge unless they are
supervised by a person who is responsible for
their safety or they have received instructions
from such a person in to how to use the
equipment safely. Children must always be
supervised in order to ensure that they do not
play with the equipment.
Keep this safety information in a safe place.

2. Layout and items supplied

2.1 Layout
1. Spindle lock
2. Additional handle
3. On/Off switch
4. Speed control
5. Pushlock button
6. Polishing / sanding disk
7. Speed indicator
8. Battery capacity indicator
9. Battery capacity indicator button
10. Sanding and polishing machine
11. Foam polishing pad
12. Synthetic fl eece bonnet
13. Abrasive paper grit 60
14. Abrasive paper grit 80
- 12 -
11.11.2019 07:52:19 11.11.2019 07:52:19